- 您現在的位置：買賣IC網 > PDF目錄376151 > MC1251A-E (Electronic Theatre Controls, Inc.) Advanced Brushless Motor Control Chipset PDF資料下載
參數資料
| 型號： | MC1251A-E |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Advanced Brushless Motor Control Chipset |
| 中文描述： | 先進的無刷電機控制芯片組 |
| 文件頁數： | 38/70頁 |
| 文件大?。?/td> | 474K |
| 代理商： | MC1251A-E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
38
Commutation Command Summary:
The following table summarizes the commands that are used in
conjunction with sinusoidal commutation:
Command
SET_PHASE_3
Function
Sets the commutation waveformfor 3-
phase brushless motors.
Sets the commutation waveformfor 2-
phase brushless motors.
Sets the phase initialization mode to
Hall-sensor-based
Sets the phase initialization mode to
algorithmc.
Sets commutation mode to encoder-
based
Sets commutation mode to
mcrostepping
Sets the encoder prescalar on
Sets the encoder prescalar off
Sets the #of encoder counts per
commutation electrical cycle.
Sets the amount of time to wait during
phase initialization
Sets the current phase angle
Sets the phase offset angle
Sets the velocity phase advance gain
Sets the logic level interpretation for the
Hall sensor inputs
Begins the algorithmc phase
initialization procedure.
Returns various commutation-related
state information set by the host
Returns the number of encoder counts
per electrical cycle
Returns the wait time used during phase
initialization
Returns the phase offset angle
Returns the phase advance gain
Returns the logic level interpretation for
the Hall sensor inputs
Returns the status of the hall sensors
Returns the current commutation angle.
SET_PHASE_2
SET_PHASE_HALL
SET_PHASE_ALGOR
SET_PHASE_ENC
SET_PHASE_MICRO
PRESCALE_ON
PRESCALE_OFF
SET_PHASE_CNTS
SET_PHASE_TIME
SET_PHASE
SET_PHASE_OFFSET
SET_KPHASE
SET_HALL_SENSE
INIT_PHASE
GET_PHASE_INFO
GET_PHASE_CNTS
GET_PHASE_TIME
GET_PHASE_OFFSET
GET_KPHASE
GET_HALL_SENSE
GET_HALLS
GET_PHASE
Motor Output Configuration
The MC1231A series of chipsets supports two motor output methods,
PWMand DAC (up to 16 bit resolution).
Below is shown a typical amplifier configuration for a 3-phase brushless
motor using the PWMoutput mode:
Axis #1 phase A
Axis #1 Phase B
Axis #1 Phase C
MC1231
Mtr #1
Mtr #2
Axis #2 phase A
Axis #2 Phase B
Axis #2 Phase C
Amplifiers
Brushless Motor (PWM Mode) Connection Scheme
In this configuration the chipset outputs 3 phased PWMmagnitude
signals per axis. These signals are then fed directly into 3 half-bridge
type voltage amplifiers.
Below is shown a typical amplifier configuration for a 3-phase brushless
motor using the DAC output mode:
Axis #1 phase A
Axis #1 Phase B
Axis #1 Phase C
MC1231
Mtr #1
Mtr #2
Axis #1
C=-(A+B)
Axis #2
C=-(A+B)
Axis #2 phase A
Axis #2 Phase B
Axis #2 Phase C
Amplifiers
Brushless Motor (DAC Mode) Connection Scheme
DAC 1A
DAC 1B
DAC 2A
DAC 2B
When using DAC output mode the digital word provided by the chipset
must first be converted into a voltage using an external DAC. Two DAC
channels are required per axis. To construct the third phase for a
brushless motor (C phase) the sumof the A and B signals must be
'negated' using C = -(A+B).
This is usually accomplished with an Op-amp circuit. In addition, if
current loop control is desired the three output signals are usually
arranged so that the sumof the currents flowing through the windings of
the motor are zero.
Motor Output Signal Interpretation
The following graph shows the desired output voltage waveformfor a
single phase.
0
+ motor command
- motor command
相關PDF資料 |
PDF描述 |
|---|---|
| MC1401A | Advanced Brushless Motor Control Chipset |
| MC1401A-P | Advanced Brushless Motor Control Chipset |
| MC1451A | Advanced Brushless Motor Control Chipset |
| MC1451A-E | Advanced Brushless Motor Control Chipset |
| MC1101A-P | Advanced Brushless Motor Control Chipset |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC-125-342 | 制造商:Brady Corporation 功能描述:WIRE MARKER SLEEVES, HEAT-SHRINK, 0.235"W, 7FT; Marker Material:PO (Polyolefin); Marker Dimensions:5.97mm x 2.134m; Legend:Blank (No Legend); Legend Color:Black; Background Color:White; Color:Black on White; Label Size:0.235"W x 7'L ;RoHS Compliant: Yes |
| MC-125-342-YL | 制造商:Brady Corporation 功能描述:WIRE MARKER SLEEVES, HEAT-SHRINK, 0.235"W, 7FT; Marker Material:PO (Polyolefin); Marker Dimensions:5.97mm x 2.134m; Legend:Blank (No Legend); Legend Color:Black; Background Color:Yellow; Color:Black on Yellow; Series:M ;RoHS Compliant: Yes |
| MC-12551-00 | 制造商:EAO International 功能描述:SWITCH SPNO |
| MC-12555-00 | 制造商:EAO International 功能描述:SWITCH SPNO R/A |
| MC125P | 制造商:Panasonic Industrial Company 功能描述:BAG MC-125PPANASONIC |
發布緊急采購，3分鐘左右您將得到回復。