- 您現在的位置：買賣IC網 > PDF目錄376151 > MC1231A (Electronic Theatre Controls, Inc.) Advanced Brushless Motor Control Chipset PDF資料下載
參數資料
| 型號： | MC1231A |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Advanced Brushless Motor Control Chipset |
| 中文描述： | 先進的無刷電機控制芯片組 |
| 文件頁數： | 49/70頁 |
| 文件大小： | 474K |
| 代理商： | MC1231A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
49
SET_AUTO_STOP_ON
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Enable automatic motor shutdown
none
45 (hex)
current axis
all axes
no
SET_AUTO_STOP_ON enables automatic motor shutdown upon
motion error. In this mode the motor will be disabled (equivalent to
MTR_OFF cmd) when a motion error occurs (see SET_POS_ERR
cmd). The motor output can be re-enabled using the MTR_ON cmd.
SET_AUTO_STOP_OFF
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Disables automatic motor shutdown
none
44 (hex)
current axis
all axes
no
SET_AUTO_STOP_OFF disables the automatic motor shutdown upon
motion error mode. In this mode the motor will not be disabled when a
motion error occurs.
Parameter Update
SET_TIME_BRK
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set break point mode to time based
none
17 (hex)
current axis
all axes
no
SET_TIME_BRK sets the current breakpoint mode to time based. In
this mode the value loaded into the breakpoint register (SET_BRK_PNT
cmd) will represent the number of sample loops since chip set power
on. After the SET_TIME_BRK command is executed, at each servo
loop the break point value will be compared against the current chip set
time. If the values are equal all profile and filter parameters will be
loaded in to the active registers. See GET_TIME cmd for information on
the chip set time. After this breakpoint condition has been satisfied, the
breakpoint mode is reset i.e. no additional breakpoints will occur until a
new breakpoint condition is set.
SET_POS_BRK
Set break point mode to positive target
position based
none
18 (hex)
current axis
all axes
no
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
SET_POS_BRK sets the current breakpoint mode to positive target
position based. In this mode the value loaded into the breakpoint
register (SET_BRK_PNT cmd) will represent the axis position in counts.
After the SET_POS_BRK command is executed, at each servo loop the
break point value will be compared against the current axis target
position. If the target position has a value equal to or greater than the
breakpoint register then all profile and all filter parameters will be
loaded in to the active registers. After this breakpoint condition has
been satisfied, the breakpoint mode is reset i.e. no additional
breakpoints will occur until a new breakpoint condition is set.
SET_NEG_BRK
Set break point mode to negative target
position based
none
19 (hex)
current axis
all axes
no
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
SET_NEG_BRK sets the current breakpoint mode to negative target
position based. In this mode the value loaded into the breakpoint
register (SET_BRK_PNT cmd) will represent the axis position in counts
After the SET_NEG_BRK command is executed, at each servo loop the
break point value will be compared against the current axis target
position. If the target position has a value equal to or less than the
breakpoint register then all profile and all filter parameters will be
loaded into the active registers. After this breakpoint condition has been
satisfied, the breakpoint mode is reset i.e. no additional breakpoints will
occur until a new breakpoint condition is set.
SET_ACTL_POS_BRK
Set break point mode to positive actual
position based
none
1b (hex)
current axis
all axes
no
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
SET_ACTL_POS_BRK sets the current breakpoint mode to positive
actual position based. In this mode the value loaded into the breakpoint
register (SET_BRK_PNT cmd) will represent the axis position in counts.
After the SET_ACTL_POS_BRK command is executed, at each servo
loop the break point value will be compared against the current axis
actual position. If the actual position has a value equal to or greater
than the breakpoint register then all profile and all filter parameters will
be loaded in to the active registers. After this breakpoint condition has
been satisfied, the breakpoint mode is reset i.e. no additional
breakpoints will occur until a new breakpoint condition is set..
相關PDF資料 |
PDF描述 |
|---|---|
| MC1241A | Advanced Brushless Motor Control Chipset |
| MC1251A | Advanced Brushless Motor Control Chipset |
| MC1251A-E | Advanced Brushless Motor Control Chipset |
| MC1401A | Advanced Brushless Motor Control Chipset |
| MC1401A-P | Advanced Brushless Motor Control Chipset |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC1231F | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC1231L | 制造商:Motorola Inc 功能描述:Logic Circuit, Quad 2-Input XNOR, ECL, 14 Pin, Ceramic, DIP |
| MC1233F | 制造商:Motorola Inc 功能描述: |
| MC1233L | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC1234L | 制造商:Motorola Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。