- 您現在的位置：買賣IC網 > PDF目錄376151 > MC1101A (Electronic Theatre Controls, Inc.) Advanced Brushless Motor Control Chipset PDF資料下載
參數資料
| 型號： | MC1101A |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Advanced Brushless Motor Control Chipset |
| 中文描述： | 先進的無刷電機控制芯片組 |
| 文件頁數： | 43/70頁 |
| 文件大?。?/td> | 474K |
| 代理商： | MC1101A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
43
Profile Generation
SET_PRFL_S_CRV
Set profile mode to S-curve point to
point
none
0b (hex)
current axis
all axes
No
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
SET_PRFL_S_CRV sets the trajectory profile mode to S-curve point to
point. In this mode, the host specifies the destination position
(SET_POS cmd), the maximumvelocity (SET_VEL cmd) the maximum
acceleration (SET_MAX_ACC cmd), and the jerk (SET_JERK cmd).
Once in this mode, the trajectory profile generator will drive the axis to
the destination position at the specified jerk while not exceeding the
maximumvelocity and max. acceleration. The axis will stay in this
profile mode until another profile mode is explicitly set.
While in this profile mode, no parameters should be changed
while the axis is in motion.
Before setting the current profile mode to S-curve point to point,
the axis should be completely at rest.
SET_PRFL_TRAP
Set profile mode to trapezoidal point to
point
none
09 (hex)
current axis
all axes
No
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
SET_PRFL_TRAP sets the trajectory profile mode to trapezoidal point
to point. In this mode, the host specifies the destination position
(SET_POS cmd), the maximumvelocity (SET_VEL cmd) and the
acceleration (SET_ACC cmd). Once in this mode, the trajectory profile
generator will drive the axis to the destination position at the specified
acceleration while not exceeding the maximumvelocity. Position and
velocity may be changed on the fly when in this profile mode;
acceleration may not. The axis will stay in this profile mode until
another profile mode is explicitly set.
Before setting the current profile mode to trapezoidal point to
point, the axis should be completely at rest.
While in this mode, the acceleration should not be changed until
the axis has come to a stop.
SET_PRFL_VEL
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set profile mode to velocity contouring.
none
0a (hex)
current axis
all axes
No
SET_PRFL_VEL sets the trajectory profile mode to velocity contouring.
In this mode the host specifies the command acceleration (SET_ACC
cmd), and the maximumvelocity (SET_VEL cmd). Once in this mode,
the trajectory profile generator will drive the axis at the specified
acceleration while not exceeding the maximumvelocity. The
acceleration and the maximumvelocity may be changed on the fly. The
axis will stay in this profile mode until another profile mode is explicitly
set. There are no limtations on changing the profile mode to velocity
contouring while the axis is in motion.
There are no host-specified limits on the position in this mode. It
is the responsibility of the host to specify profile parameters that
maintain the axis within safe position limits.
SET_PRFL_GEAR
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set profile mode to electronic gear
none
0c (hex)
current axis
axis #1, #2 (see chart)
No
SET_PRFL_GEAR, sets the trajectory profile mode to electronic gear.
In this mode the host specifies the gear ratio (SET_RATIO cmd). Once
in this mode the trajectory profile generator will drive the current (slave)
axis to the position specified by the master axis factored by the
specified gear ratio. The gear ratio may be changed on the fly. The axis
will stay in this profile mode until another profile mode is explicitly set.
The electronic gear mode is available on the following axis for each
chipset:
chipset p/n
MC1231A
MC1131A
gear pairs (master -> slave)
#2 -> #1
not available
There are no host-specified limits to axis motion in this mode. It is
the responsibility of the host to specify a gear ratio that maintains
the axis within safe motion limits.
SET_POS
Data/direction
Encoding:
Axis acted on:
Available on:
Double buffered:
Set command position
2/write
10 (hex)
current axis
all axes
yes
SET_POS sets the final position used during the S-curve and
trapezoidal trajectory profile generator modes. The position is specified
as a signed 32-bit number with units of counts. The range is
相關PDF資料 |
PDF描述 |
|---|---|
| MC1131A | Advanced Brushless Motor Control Chipset |
| MC1141A | Advanced Brushless Motor Control Chipset |
| MC1151A | Advanced Brushless Motor Control Chipset |
| MC1151A-E | Advanced Brushless Motor Control Chipset |
| MC1201A | Advanced Brushless Motor Control Chipset |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC1101A-P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Advanced Brushless Motor Control Chipset |
| MC110M | 制造商:Thomas & Betts 功能描述:10A,INSERT,MALE,M10P |
| MC112061P | 制造商:LANSDALE 制造商全稱:LANSDALE Semiconductor Inc. 功能描述:Crystal Oscillator |
| MC1121 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:100mA Charge Pump Voltage Converter with Shutdown |
| MC1121DMR2 | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:ON Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。