MC10E1651
http://onsemi.com
3
Table 3. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
VSUP
Total Supply Voltage
|VEE| + |VCC|
12.0
V
VPP
Differential Input Voltage
|V1 V2|
3.7
V
VI
Input Voltage
VEE v VI v VCC
V
Iout
Output Current
Continuous
Surge
50
100
mA
TA
Operating Temperature Range
0 to +85
°C
Tstg
Storage Temperature Range
65 to +150
°C
qJA
Thermal Resistance (JunctiontoAmbient)
0 lfpm
500 lfpm
28 PLCC
63.5
43.5
°C/W
qJC
Thermal Resistance (JunctiontoCase)
Standard Board
28 PLCC
22 to 26
°C/W
VEE
Operating Range
GND = 0 V
4.2 to 5.7
V
Tsol
Wave Solder
PbFree v 3 sec @ 260°C
265
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 4. DC CHARACTERISTICS VCC = +5.0 V ±5%; VEE = 5.2 V ±5%, GND = 0 V (Note 1) 0°C
25°C
85°C
Symbol
Characteristic
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
VOH
Output HIGH Voltage (Note
1)1020
840
980
810
920
735
mV
VOL
Output Low Voltage (Note
1)1950
1630 1950
1600
mV
VIL
Input LOW Voltage (LEN) (Note
1)1.95
1.48
1.95
1.48
1.95
1.45
mV
VIH
Input HIGH Voltage (LEN) (Note
1)1.17
0.84
1.13
0.81
1.07
0.735
mV
II
IIH
Input Current (V1, V2)
Input HIGH Current (LEN)
65
150
65
150
65
150
mA
ICC
IEE
Positive Supply Current
Negative Supply Current
50
55
50
55
50
55
mA
VCMR
Common Mode Range (Note
2)2.0
3.0
2.0
3.0
2.0
3.0
V
Hys
Hysteresis
27
30
mV
Vskew
1.0
0
mV
Cin
Input Capacitance
PLCC
2
pF
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input VIL and VIH parameters vary 1:1 with VCC. Output VOH and VOL parameters vary 1:1 with GND.
2. VCMR Min varies 1:1 with VEE; Max varies 1:1 with VCC.
3. Hysteresis skew (Vskew) is provided to indicate the offset of the hysteresis window. For example, at 25°C the nominal hysteresis value is
27 mV and the Vskew value indicates that the hysteresis was skewed from the reference level by 1mV in the negative direction. Hence the
hysteresis window ranged from 14 mV below the reference level to 13 mV above the reference level. All hysteresis measurements were
determined using a reference voltage of 0 mV.