參數資料
型號: MC100E211FN
廠商: MOTOROLA INC
元件分類: 時鐘及定時
英文描述: 1:6 DIFFERENTIAL CLOCK DISTRIBUTION CHIP
中文描述: 100E SERIES, LOW SKEW CLOCK DRIVER, 6 TRUE OUTPUT(S), 6 INVERTED OUTPUT(S), PQCC28
封裝: PLASTIC, LCC-28
文件頁數: 1/7頁
文件大小: 101K
代理商: MC100E211FN
SEMICONDUCTOR TECHNICAL DATA
2–1
REV 3
Motorola, Inc. 1996
5/95
The MC10E/100E211 is a low skew 1:6 fanout device designed
explicitly for low skew clock distribution applications. The device can be
driven by either a differential or single-ended ECL or, if positive power
supplies are used, PECL input signal (PECL is an acronym for Positive
ECL, PECL levels are ECL levels referenced to +5V rather than ground).
If a single-ended input is to be used the VBB pin should be connected to
the CLK input and bypassed to ground via a 0.01
μ
F capacitor. The VBB
supply is designed to act as the switching reference for the input of the
E211 under single-ended input conditions, as a result this pin can only
source/sink up to 0.5mA of current.
Guaranteed Low Skew Specification
Synchronous Enabling/Disabling
Multiplexed Clock Inputs
VBB Output for Single-Ended Use
Internal 75k
Input Pulldown Resistors
Common and Individual Enable/Disable Control
High Bandwidth Output Transistors
Extended 100E VEE Range of –4.2V to –5.46V
The E211 features a multiplexed clock input to allow for the distribution
of a lower speed scan or test clock along with the high speed system
clock. When LOW (or left open in which case it will be pulled LOW by the
input pulldown resistor) the SEL pin will select the differential clock input.
Both a common enable and individual output enables are provided. When asserted the positive output will go LOW on the next
negative transition of the CLK (or SCLK) input. The enabling function is synchronous so that the outputs will only be
enabled/disabled when the outputs are already in the LOW state. In this way the problem of runt pulse generation during the
disable operation is avoided. Note that the internal flip flop is clocked on the falling edge of the input clock edge, therefore all
associated specifications are referenced to the negative edge of the CLK input.
The output transitions of the E211 are faster than the standard ECLinPS
edge rates. This feature provides a means of
distributing higher frequency signals than capable with the E111 device. Because of these edge rates and the tight skew limits
guaranteed in the specification, there are certain termination guidelines which must be followed. For more details on the
recommended termination schemes please refer to the applications information section of this data sheet.
FUNCTION TABLE
CLK
SCLK
SEL
ENx
Q
H/L
X
Z*
X
H/L
Z*
L
H
X
L
L
H
CLK
SCLK
L
* Z = Negative transition of CLK or SCLK
ECLinPS is a trademark of Motorola Inc.
1:6 DIFFERENTIAL
CLOCK DISTRIBUTION CHIP
FN SUFFIX
PLASTIC PACKAGE
CASE 776-02
相關PDF資料
PDF描述
MC10E211 Replaced by TPS2055A : 0.345A, 2.7-5.5V Single Hi-Side MOSFET, Fault Report, Act-High Enable 8-PDIP -40 to 85
MC10E211FN 1:6 DIFFERENTIAL CLOCK DISTRIBUTION CHIP
MC100EP111 Low-Voltage 1:10 Differential ECL/PECL/HSTL Clock Driver(低壓1:10差分ECL/PECL/HSTL時鐘驅動器)
MC100H603FN 9-Bit Latch ECL/TTL Translator
MC10H603 9-Bit Latch ECL/TTL Translator
相關代理商/技術參數
參數描述
MC100E211FNG 功能描述:時鐘驅動器及分配 5V ECL Diff Clock Distribution RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel
MC100E211FNR2 功能描述:時鐘驅動器及分配 5V ECL Diff Clock RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel
MC100E211FNR2G 功能描述:時鐘驅動器及分配 5V ECL Diff Clock Distribution RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel
MC100E212 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:3-BIT SCANNABLE REGISTERED ADDRESS DRIVER
MC100E212FN 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:5V ECL 3-Bit Scannable Registered Address Driver