參數資料
型號: MBM29LV004BC
廠商: Fujitsu Limited
英文描述: 4M (512K X 8) BIT
中文描述: 4分(為512k × 8)位
文件頁數: 19/52頁
文件大?。?/td> 442K
代理商: MBM29LV004BC
19
MBM29LV004TC
-70/-90/-12
/MBM29LV004BC
-70/-90/-12
Extended Command
(1) Fast Mode
MBM29LV004TC/BC has Fast Mode function. This mode dispenses with the initial two unclock cycles
required in the standard program command sequence by writing Fast Mode command into the command
register. In this mode, the required bus cycle for programming is two cycles instead of four bus cycles in
standard program command. (Do not write erase command in this mode.) The read operation is also executed
after exiting this mode. To exit this mode, it is necessary to write Fast Mode Reset command into the command
register. (Refer to the Figure 24 Extended algorithm.) The V
CC
active current is required even CE = V
IH
during
Fast Mode.
(2) Fast Programming
During Fast Mode, the programming can be executed with two bus cycles operation. The Embedded Program
Algorithm is executed by writing program set-up command (A0H) and data write cycles (PA/PD). (Refer to
the Figure 24 Extended algorithm.)
(3) Extended Sector Protection
In addition to normal sector protection, the MBM29LV004TC/BC has Extended Sector Protection as extended
function. This function enable to protect sector by forcing V
ID
on RESET pin and write a commnad sequence.
Unlike conventional procedure, it is not necessary to force V
ID
and control timing for control pins. The only
RESET pin requires V
ID
for sector protection in this mode. The extended sector protect requires V
ID
on RESET
pin. With this condition, the operation is initiated by writing the set-up command (60H) into the command
register. Then, the sector addresses pins (A
18
, A
17
, A
16
, A
15
, A
14
, and A
13
) and (A
10
, A
6
, A
1
, A
0
) = (0, 0, 1, 0)
should be set to the sector to be protected (recommend to set V
IL
for the other addresses pins), and write
extended sector protect command (60H). A sector is typically protected in 150
μ
s. To verify programming of
the protection circuitry, the sector addresses pins (A
18
, A
17
, A
16
, A
15
, A
14
, and A
13
) and (A
10
, A
6
, A
1
, A
0
) = (0,
0, 1, 0) should be set and write a command (40H). Following the command write, a logical “1” at device
output DQ
0
will produce for protected sector in the read operation. If the output data is logical “0”, please
repeat to write extended sector protect command (60H) again. To terminate the operation, it is necessary
to set RESET pin to V
IH
.
相關PDF資料
PDF描述
MBM29LV004TC 4M (512K X 8) BIT
MBM29LV004TC-70PNS 4M (512K X 8) BIT
MBM29LV004BC-90PNS 4M (512K X 8) BIT
MBM29LV004TC-90PNS 4M (512K X 8) BIT
MBM29LV004BC-70PNS 4M (512K X 8) BIT
相關代理商/技術參數
參數描述
MBM29LV004BC-12 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT
MBM29LV004BC-12PNS 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT
MBM29LV004BC-12PTN 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT
MBM29LV004BC-12PTR 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT
MBM29LV004BC-70 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:4M (512K X 8) BIT