- 您現在的位置：買賣IC網 > PDF目錄377946 > MBM29F800TA-55PFTR (FUJITSU LTD) 122 x 32 pixel format, Compact LCD size PDF資料下載
參數資料
| 型號： | MBM29F800TA-55PFTR |
| 廠商： | FUJITSU LTD |
| 元件分類： | DRAM |
| 英文描述： | 122 x 32 pixel format, Compact LCD size |
| 中文描述： | 512K X 16 FLASH 5V PROM, 55 ns, PDSO48 |
| 封裝： | PLASTIC, REVERSE, TSOP1-48 |
| 文件頁數： | 12/48頁 |
| 文件大?。?/td> | 537K |
| 代理商： | MBM29F800TA-55PFTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
12
MBM29F800TA
-55/-70/-90
/MBM29F800BA
-55/-70/-90
To activate this mode, the programming equipment must force V
ID
on address pin A
9
and control pin OE, (suggest
V
ID
= 11.5V), CE = V
IL
, and A
6
= V
IL
. The sector addresses (A
18
, A
17
, A
16
, A
15
, A
14
, A
13
, and A
12
) should be set to
the sector to be protected. Tables 5 and 6 define the sector address for each of the nineteen (19) individual
sectors. Programming of the protection circuitry begins on the falling edge of the WE pulse and is terminated
with the rising edge of the same. Sector addresses must be held constant during the WE pulse. See Figures 16
and 23 for sector protection waveforms and algorithm.
To verify programming of the protection circuitry, the programming equipment must force V
ID
on address pin A
9
with CE and OE at V
IL
and WE at V
IH
. Scanning the sector addresses (A
18
, A
17
, A
16
, A
15
, A
14
, A
13
, and A
12
) while
(A
6
, A
1
, A
0
) = (0, 1, 0) will produce a logical “1” code at device output DQ
0
for a protected sector. Otherwise the
devices will read 00H for unprotected sector. In this mode, the lower order addresses, except for A
0
, A
1
, and A
6
are DON’T CARES. Address locations with A
1
= V
IL
are reserved for Autoselect manufacturer and device codes.
A
-1
requires to apply to V
IL
on byte mode.
It is also possible to determine if a sector is protected in the system by writing an Autoselect command. Performing
a read operation at the address location XX02H, where the higher order addresses (A
18
, A
17
, A
16
, A
15
, A
14
, A
13
,
and A
12
) are the desired sector address will produce a logical “1” at DQ
0
for a protected sector. See Tables 4.1
and 4.2 for Autoselect codes.
Temporary Sector Unprotection
This feature allows temporary unprotection of previously protected sectors of the MBM29F800TA/BA device in
order to change data. The Sector Unprotection mode is activated by setting the RESET pin to high voltage (12
V). During this mode, formerly protected sectors can be programmed or erased by selecting the sector addresses.
Once the 12 V is taken away from the RESET pin, all the previously protected sectors will be protected again.
Refer to Figures 17 and 24.
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29F800TA-70PF | 8M (1M X 8/512K X 16) BIT |
| MBM29F800TA-70PFTN | 8M (1M X 8/512K X 16) BIT |
| MBM29F800TA-70PFTR | 8M (1M X 8/512K X 16) BIT |
| MBM29F800TA-90PF | Replaced by TPS2045A : 0.345A, 2.7-5.5V Single Hi-Side MOSFET, Fault Report, Act-Low Enable 8-PDIP -40 to 85 |
| MBM29F800TA-90PFTN | 8M (1M X 8/512K X 16) BIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM29F800TA-70 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8M (1M X 8/512K X 16) BIT |
| MBM29F800TA-70PF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8M (1M X 8/512K X 16) BIT |
| MBM29F800TA-70PF-S# | 制造商:FUJITSU 功能描述: |
| MBM29F800TA-70PFTN | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8M (1M X 8/512K X 16) BIT |
| MBM29F800TA-70PFTN-SFL(E1) | 制造商:Fujitsu 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。