參數資料
型號： MB96F348RWAPMC-GE2
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP100
封裝： 14 X 14 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LFQFP-100
文件頁數： 111/159頁
文件大?。?/td> 2625K
代理商： MB96F348RWAPMC-GE2
Preliminary Specication
MB96300
FME/EMDC- 2007-02-12
MB96300_shortspec.fm
55
PRELIMINARY
s HANDLING DEVICES
Special care is required for the following when handling the device:
Preventing latch-up
Treatment of unused pins
Using external clock
Precautions for when not using a sub clock signal
Notes on during operation of PLL clock mode
Power supply pins (VCC/VSS)
Crystal Oscillator Circuit
Turning-on Sequence of Power Supply to A/D Converter and Analog Inputs
Connection of Unused Pins of A/D Converter
Notes on Energization
Stabilization of power supply voltage
1.
Preventing latch-up
CMOS IC chips may suffer latch-up under the following conditions:
A voltage higher than VCC or lower than VSS is applied to an input or output pin.
A voltage higher than the rated voltage is applied between VCC and VSS.
The AVCC power supply is applied before the VCC voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
For the same reason, also be careful not to let the analog power-supply voltage (AVCC, AVRH) exceed the
digital power-supply voltage.
2.
Treatment of unused pins
Unused input pins may be left open when the input is disabled (corresponding bit of Port Input Enable register
PIER = 0).
Leaving unused input pins open when the input is enabled may result in misbehavior and possible permanent
damage of the device. Therefore they must be pulled up or pulled down through resistors. To prevent latchup,
those resistors should be more than 2 kOhm.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with either
input disabled or external pull-up/pull-down resistor as described above.
3.
Using external clock
To use external clock, drive the X0 pin and leave X1 pin open.
4.
Precautions for when not using a sub clock signal
If you do not connect pins X0A and X1A to an oscillator, use a pull-down resistor on the X0A pin, and
leave the X1A pin open.
5.
Notes on during operation of PLL clock mode
If the PLL clock mode is selected and no external oscillator is operating or no external clock is supplied, the
microcontroller attempts to be working with the freely oscillating PLL. Performance of this operation, however,
cannot be guaranteed.
6.
Power supply pins (VCC/VSS)
Ensure that all VCC-level power supply pins are at the same potential. In addition, ensure the same for all
VSS-level power supply pins. If there are more than one VCC or VSS system, the device may operate
incorrectly even within the guaranteed operating range.
相關PDF資料
PDF描述
MB96F346AWAPMC-GE2 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP100
MB96F348CSAPMC-GE2 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP100
MB96F347RWAPQC-GE2 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP100
MB96F348CSAPQC-GE2 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP100
MB96F356YSAPMC1-GE2 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64
相關代理商/技術參數
參數描述
MB96F348RWAPQC-GE2 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
MB96F348TSAPMC-GE2 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
MB96F348TSAPQC-GE2 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
MB96F348TSB 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
MB96F348TWAPMC-GE2 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*