參數資料
型號: MB95F156JPMT-GE1
廠商: Fujitsu Semiconductor America Inc
文件頁數: 5/68頁
文件大小: 0K
描述: IC MCU FLASH 32K ROM 48LQFP
標準包裝: 1
系列: F²MC MB95150M
核心處理器: F²MC-8FX
芯體尺寸: 8-位
速度: 16MHz
連通性: LIN,SIO,UART/USART
外圍設備: LCD,LVD,POR,PWM,WDT
輸入/輸出數: 39
程序存儲器容量: 32KB(32K x 8)
程序存儲器類型: 閃存
RAM 容量: 1K x 8
電壓 - 電源 (Vcc/Vdd): 2.4 V ~ 5.5 V
數據轉換器: A/D 8x8/10b
振蕩器型: 外部
工作溫度: -40°C ~ 85°C
封裝/外殼: 48-LQFP
包裝: 托盤
產品目錄頁面: 722 (CN2011-ZH PDF)
其它名稱: 865-1076
MB95F156JJPMT-GE1
MB95150M Series
13
■ HANDLING DEVICES
Preventing Latch-up
Care must be taken to ensure that maximum voltage ratings are not exceeded when they are used.
Latch-up may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- and high-withstand voltage pins or if higher than the rating voltage is applied between VCC
pin and VSS pin.
When latch-up occurs, power supply current increases rapidly and might thermally damage elements.
Stable Supply Voltage
Supply voltage should be stabilized.
A sudden change in power-supply voltage may cause a malfunction even within the guaranteed operating range
of the Vcc power-supply voltage.
For stabilization, in principle, keep the variation in Vcc ripple (p-p value) in a commercial frequency range
(50/60 Hz) not to exceed 10% of the standard Vcc value and suppress the voltage variation so that the transient
variation rate does not exceed 0.1 V/ms during a momentary change such as when the power supply is switched.
Precautions for Use of External Clock
Even when an external clock is used, oscillation stabilization wait time is required for power-on reset, wake-up
from sub clock mode or stop mode.
■ PIN CONNECTION
Treatment of Unused Pin
Leaving unused input pins unconnected can cause abnormal operation or latch-up, leaving to permanent dam-
age. Unused input pins should always be pulled up or down through resistance of at least 2 k
. Any unused
input/output pins may be set to output mode and left open, or set to input mode and treated the same as unused
input pins. If there is unused output pin, make it to open.
Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
F between VCC and VSS pins
near this device.
相關PDF資料
PDF描述
VI-B2L-IX-F1 CONVERTER MOD DC/DC 28V 75W
ADUC7061BCPZ32-RL IC MCU 16/32BIT 32KB 32LFCSP
VI-B2L-IW-F4 CONVERTER MOD DC/DC 28V 100W
ATMEGA8535L-8JU MCU AVR 8K ISP FLASH MEM 44-PLCC
VI-B2L-IW-F3 CONVERTER MOD DC/DC 28V 100W
相關代理商/技術參數
參數描述
MB95F156M 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontroller
MB95F156MPMC 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontroller
MB95F156MPMT 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontroller
MB95F156N 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontroller
MB95F156NPMC 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontroller