- 您現在的位置：買賣IC網 > PDF目錄377933 > MB95F108ANW (Fujitsu Limited) 8-bit Proprietary Microcontrollers(8位微控制器) PDF資料下載
參數資料
| 型號： | MB95F108ANW |
| 廠商： | Fujitsu Limited |
| 英文描述： | 8-bit Proprietary Microcontrollers(8位微控制器) |
| 中文描述： | 8位微控制器專利（8位微控制器） |
| 文件頁數： | 34/72頁 |
| 文件大小： | 739K |
| 代理商： | MB95F108ANW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
MB95100AM Series
34
(Continued)
*1 : The parameter is based on AV
SS
=
V
SS
=
0.0 V.
*2 : Apply equal potential to AVcc and Vcc. AVR should not exceed AVcc
+
0.3 V.
*3 : V
I
and Vo should not exceed V
CC
+
0.3 V. V
I
must not exceed the rating voltage. However, if the maximum current
to/from an input is limited by some means with external components, the I
CLAMP
rating supersedes the V
I
rating.
*4 : Applicable to pins : P00 to P07, P10 to P14, P20 to P24, P30 to P37, P40 to P43, P52, P53, P70, P71,
PE0 to PE3
Use within recommended operating conditions.
Use at DC voltage (current).
+
B signal is an input signal that exceeds V
CC
voltage. The
+
B signal should always be applied a limiting
resistance placed between the
+
B signal and the microcontroller.
The value of the limiting resistance should be set so that when the
+
B signal is applied the input current
to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input
potential may pass through the protective diode and increase the potential at the V
CC
pin, and this affect
other devices.
Note that if the
+
B signal is inputted when the microcontroller power supply is off (not fixed at 0 V), the power
supply is provided from the pins, so that incomplete operation may result.
Note that if the
+
B input is applied during power-on, the power supply is provided from the pins and the
resulting power supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the
+
B input pin open.
Sample recommended circuits :
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
Parameter
Symbol
Rating
Unit
Min
40
55
Max
Power consumption
Pd
320
+
85
+
150
mW
°
C
°
C
Operating temperature
T
A
Storage temperature
Tstg
P-ch
N-ch
Vcc
R
Input/Output Equivalent circuits
+
B input (0 V to 16 V)
Limiting
resistance
Protective diode
相關PDF資料 |
PDF描述 |
|---|---|
| MB95F104AJS | 8-bit Proprietary Microcontrollers(8位微控制器) |
| MB95F104AJW | 8-bit Proprietary Microcontrollers(8位微控制器) |
| MB95F104AMS | 8-bit Proprietary Microcontrollers(8位微控制器) |
| MB95F104AMW | 8-bit Proprietary Microcontrollers(8位微控制器) |
| MB95F104ANS | 8-bit Proprietary Microcontrollers(8位微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB95F108ANWPFM | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB95F108ANWPFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB95F108ANWPMC1-GE1 | 制造商:FUJITSU 功能描述:8-bit Proprietary Microcontrollers 制造商:FUJITSU 功能描述:8-Bit MCU |
| MB95F108ANWPMC-GE1 | 制造商:FUJITSU 功能描述:8-bit Proprietary Microcontrollers |
| MB95F108AS | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。