參數資料
型號： MB91F777RPMC-ESE1
廠商： FUJITSU LTD
元件分類： 微控制器/微處理器
英文描述： RISC MICROCONTROLLER, PQFP144
封裝： 20 X 20 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-144
文件頁數： 46/120頁
文件大小： 4532K
代理商： MB91F777RPMC-ESE1
MB91770 Series
DS07-16913-1E
31
■ HANDLING DEVICE
For latch-up prevention
If a voltage higher than VCC or a voltage lower than VSS is applied to an I/O pin, or if a voltage exceeding the
ratings is applied between VCC and VSS pins, a latch-up may occur in CMOS IC. If the latch-up occurs, the power
supply current increases excessively and device elements may be damaged by heat. Take care to prevent any
voltage from exceeding the maximum ratings in device application.
Also, the power supply (AVCC, AVRH) to the analog system, analog input, and power supply to high-current output
buffer pins must not exceed the digital power supply (VCC) when the power supply to the analog system and
high-current output buffer pins is turned on or off.
If the voltage is applied to the power supply pin for LCD (V3 to V0 pins), be sure not to exceed the power supply
voltage (VCC).
In the correct power-on sequence, turn on the digital power supply (VCC), analog power supplies (AVCC, AVRH)
and power supply to high current output buffer (DVCC) simultaneously. Or, turn on the digital power supply (VCC)
first, and then turn on analog power supplies (AVCC, AVRH) and power supply to high current output buffer (DVCC).
Treatment of unused pins
If unused input pins are left open, they may cause a permanent damage to the device due to device malfunction
or latch-up. Connect a 2 k
Ω or higher resistor to each of unused input pins for pull-up or pull-down processing.
Also, if I/O pins are not used, they must be set to the output state for releasing or they must be set to the input
state and treated in the same way as for the input pins.
Power supply pins
The device is designed to ensure that if the device contains multiple Vcc or Vss pins, the pins that should be at
the same potential are interconnected to prevent latch-up or other malfunctions. Further, connect these pins to
an external power supply or ground to reduce unwanted radiation, prevent strobe signals from malfunctioning
due to a raised ground level, and fulfill the total output current standard, etc. As shown below , all VSS power
supply pins must be treated in the similar way. If multiple VCC or VSS systems are connected, the device cannot
operate correctly even within the guaranteed operating range.
Power Supply Input Pins
The power supply pins should be connected to VCC and VSS pins of this device at the low impedance from the
power supply source.
In the area close to this device, a ceramic capacitor having the capacitance larger than the capacitor of C pin is
recommended to connect as a bypass capacitor between VCC and VSS pins.
V
CC
V
SS
V
CC
V
CC
V
SS
V
SS
V
CC
V
CC
V
SS
V
SS
相關PDF資料
PDF描述
MB91F775RPMC-ESE1 RISC MICROCONTROLLER, PQFP144
MB91FV319RPMC-ESE1 32-BIT, FLASH, 40.8 MHz, RISC MICROCONTROLLER, PQFP176
MB91F318SPMC-GXXX-XXXXE1 32-BIT, FLASH, 40.8 MHz, RISC MICROCONTROLLER, PQFP176
MB91F318RPMC-G-XXXE1 32-BIT, FLASH, 40.8 MHz, RISC MICROCONTROLLER, PQFP176
MB91F318RPMC-GXXX-XXXXE1 32-BIT, FLASH, 40.8 MHz, RISC MICROCONTROLLER, PQFP176
相關代理商/技術參數
參數描述
MB91FV130CR-ES 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-Bit RISC Microcontroller
MB91FV310A 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Proprietary 32-bit Microcontroller CMOS
MB91FV310APFV-ES 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Proprietary 32-bit Microcontroller CMOS
MB91FV319A 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller
MB91FV319APMT-ES 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*