參數資料
型號： MB91F356BPMT
元件分類： 微控制器/微處理器
英文描述： RISC MICROCONTROLLER, PQFP176
封裝： 24 X 24 MM, 1.70 MM HEIGHT, 0.50 MM PPITCH, LEAD FREE, PLASTIC, LQFP-176
文件頁數： 59/140頁
文件大?。?/td> 3803K
代理商： MB91F356BPMT
MB91350A Series
DS07-16503-5E
25
Pull-up Control
If a pull-up resistor is provided to a pin that is used as an external bus pin, there is no guarantee that the pin will
conform to the specifications given in “
■ ELECTRICAL CHARACTERISTICS 4. AC Characteristics (4) Normal
Bus Access Read/Write Operation, (5) Multiplex Bus Access Read/Write operation and (7) Hold Timing”.
Furthermore, even if a port has been configured to use a pull-up resistance, this setting is invalid during stop
mode with HIZ=1 and during hardware standby mode.
Sub Clock Select
At least one NOP instruction needs to be executed immediately after switching the clock source from main clock
mode to sub clock mode.
Bit Search Module
The BSD0, BSD1, and BDSC registers can only be accessed in words.
D-bus Memory
Do not set the code area to memory on the D-bus because instructions cannot be fetched from the D-bus.
Executing an instruction fetch to the D-bus area will cause incorrect data to be interpreted as code, possibly
causing the device to run out of control.
Low Power Consumption Mode
When entering sleep or stop mode, be sure to read the standby control register (STCR) immediately after writing
to it.
More specifically, use the following sequence.
Furthermore, after recovering from standby mode, set the I flag, ILM, and ICR registers such that the CPU
branches to the interrupt handler for the interrupt that triggered the controller to recover from standby mode.
Switching the Function of Shared Ports
Use the Port Function Register (PFR) to switch between using an external pin as a port or a shared pin. Note,
however, that bus pins are switched depending on the external bus settings.
(Idi
#0x0b, r0)
(Idi
#_CLKR, r12)
stb
r0, @r12
// sub-clock mode
nop
// Must insert NOP instruction
(Idi
#value_of_standby, r0)
(Idi
#_STCR, r12)
stb
r0, @r12
// set STOP/SLEEP bit
Idub @r12, r0
// Must read STCR
Idub @r12, r0
// after reading, go into standby mode
NOP
// Must insert NOP
× 5
NOP
相關PDF資料
PDF描述
MB91461PMC-GSE1 RISC MICROCONTROLLER, PQFP176
MB91664PMC 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP120
MB91661PMC 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP120
MB91F155PFV-G 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP144
MB91F218SPMC-GTE1 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP144
相關代理商/技術參數
參數描述
MB91F357B 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller
MB91F357BPMT 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller
MB91F361GAPFVS 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller
MB91F362GAPFVS 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller
MB91F362GAPFVS-G-N2E1 功能描述:IC MCU 32BIT 512KB FLASH 制造商:cypress semiconductor corp 系列:FR MB91360G 零件狀態:在售 核心處理器:FR50 RISC 核心尺寸:32-位 速度:64MHz 連接性:CAN，I2C，串行輸入/輸出，UART/USART 外設:DMA，POR，PWM，WDT I/O 數:160 程序存儲容量:512KB（512K x 8） 程序存儲器類型:閃存 EEPROM 容量:- RAM 容量:20K x 8 電壓 - 電源（Vcc/Vdd）:4.25 V ~ 5.25 V 數據轉換器:A/D 8x10b，D/A 2x10b 振蕩器類型:外部 工作溫度:-40°C ~ 85°C（TA） 標準包裝:24
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*