- 您現在的位置：買賣IC網 > PDF目錄377926 > MB90V540CR (FUJITSU LTD) 16-bit Proprietary Microcontroller PDF資料下載
參數資料
| 型號： | MB90V540CR |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-bit Proprietary Microcontroller |
| 中文描述： | 16-BIT, 16 MHz, MICROCONTROLLER, CPGA256 |
| 封裝： | PGA-256 |
| 文件頁數： | 15/56頁 |
| 文件大?。?/td> | 757K |
| 代理商： | MB90V540CR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
MB90540/545 Series
15
I
HANDLING DEVICES
(1)
Preventing latch-up
CMOS IC chips may suffer latch-up under the following conditions:
A voltage higher than Vcc or lower than Vss is applied to an input or output pin.
A voltage higher than the rated voltage is applied between Vcc and Vss.
The AVcc power supply is applied before the Vcc voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
For the same reason, care must also be taken in not allowing the analog power-supply voltage (AVcc, AVRH,
DVcc) to exceed the digital power-supply voltage.
(2)
Handling unused input pins
Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the
device. Therefor they must be pulled up or pulled down through resistors. In this case those resistors should be
more than 2 k
.
Unused bi-directional pins should be set to the output state and can be left open, or the input state with the
above described connection.
(3)
Using external clock
To use external clock, drive X0 pin only and leave X1 pin unconnected.
Below is a diagram of how to use external clock.
(4)
Not using subclock mode
Oscillations must be connected to the X0A and X1A, even when a subclock is not used.
(5)
Power supply pins (Vcc/Vss)
In products with multiple V
CC
or V
SS
pins, the pins of a same potential are internally connected in the device to
avoid abnormal operations including latch-up. However you must connect the pins to an external power and a
ground line to lower the electro-magnetic emission level to prevent abnormal operation of strobe signals caused
by the rise in the ground level, and to conform to the total current rating.
Make sure to connect V
CC
and V
SS
pins via the lowest impedance to power lines.
It is recommended to provide a bypass capacitor of around 0.1
μ
F between V
CC
and V
SS
pins near the device.
X0
X1
MB90540/545 Series
Open
Vcc
Vss
Vss
Vcc
Vss
Vcc
MB90540/545
Series
Vcc
Vss
Vcc
Vss
相關PDF資料 |
PDF描述 |
|---|---|
| MB90V540G | 16-bit Proprietary Microcontroller |
| MB90F549G | Octal Bus Transceivers And Registers With 3-State Outputs 24-CDIP -55 to 125 |
| MB90F549PF | 16-bit Proprietary Microcontroller |
| MB90F549PFV | 16-bit Proprietary Microcontroller |
| MB90F553A | Octal Bus Transceivers And Registers With 3-State Outputs 24-CFP -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB-910 | 制造商:Circuit Test 功能描述:BREADBOARD WIRING KIT - 350 PCS |
| MB9100100 | 制造商:COM/DUO 功能描述:FAN 4-6WKS |
| MB9100-100 | 制造商:COM/DUO 功能描述:FAN 4-6WKS |
| MB91101 | 制造商:Panasonic Industrial Company 功能描述:IC |
| MB91101A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。