- 您現在的位置：買賣IC網 > PDF目錄377922 > MB90F962PMT (FUJITSU LTD) 16-bit Microcontroller PDF資料下載
參數資料
| 型號： | MB90F962PMT |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-bit Microcontroller |
| 中文描述： | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-48 |
| 文件頁數： | 13/51頁 |
| 文件大?。?/td> | 790K |
| 代理商： | MB90F962PMT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
MB90960 Series
13
■
HANDLING DEVICES
Special care is required for the following when handling the device :
Preventing latch-up
Treatment of unused pins
Using external clock
Notes on during operation of PLL clock mode
Power supply pins (V
CC
/V
SS
)
Pull-up/down resistors
Crystal oscillator circuit
Turning-on sequence of power supply to A/D converter and analog inputs
Connection of unused pins of A/D converter
Notes on energization
Stabilization of power supply voltage
Initialization
Correspondence with
+
105
°
C or more
1.
Preventing latch-up
CMOS IC chips may suffer latch-up under the following conditions :
A voltage higher than V
CC
or lower than V
SS
is applied to an input or output pin.
A voltage higher than the rated voltage is applied between V
CC
and V
SS
.
The AV
CC
power supply is applied before the V
CC
voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
When used, note that maximum rated voltage is not exceeded.
For the same reason, also be careful not to let the analog power-supply voltage (AV
CC
, AVR) exceed the digital
power-supply voltage.
2.
Treatment of unused pins
Leaving unused input pins open may result in misbehavior or latch-up and possible permanent damage of the
device. Therefore, they must be pulled up or pulled down through resistors. In this case, those resistors should
be more than 2 k
.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
3.
Using external clock
To use external clock, drive the X0 (X0A) pin and leave X1 (X1A) pin open.
MB90960 Series
X0 (X0A)
X1 (X1A)
Open
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F962S | 16-bit Microcontroller |
| MB90F962SPMT | 16-bit Microcontroller |
| MB90980 | 16-bit Proprietary Microcontroller |
| MB90982 | 16-bit Proprietary Microcontroller |
| MB90F983 | 16-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F962SPMCR-GE1 | 制造商:FUJITSU 功能描述:IC MCU 16BIT 16LX 48LQFP |
| MB90F962SPMCR-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB90V340A-102CR | 制造商:FUJITSU 功能描述: |
| MB-910 | 制造商:Circuit Test 功能描述:BREADBOARD WIRING KIT - 350 PCS |
| MB9100100 | 制造商:COM/DUO 功能描述:FAN 4-6WKS |
發布緊急采購，3分鐘左右您將得到回復。