- 您現在的位置：買賣IC網 > PDF目錄377922 > MB90F927PF-GE1 (FUJITSU LTD) 16-bit Microcontrolle PDF資料下載
參數資料
| 型號： | MB90F927PF-GE1 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-bit Microcontrolle |
| 中文描述： | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, 3.35 MM HEIGHT, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件頁數： | 36/63頁 |
| 文件大?。?/td> | 941K |
| 代理商： | MB90F927PF-GE1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
MB90925 Series
36
(Continued)
*6 : Average total output current is defined as the value of the average current flowing over 100 ms at all of the
corresponding pins. The “average value” can be calculated from the formula of “operating current” times
“ operating factor”.
*7 :
Applicable to pins : P10 to P15, P50 to P57, P70 to P77, P80 to P87
Use within recommended operating conditions.
Use at DC voltage (current) .
The
+
B signal should always be applied with a limiting resistance placed between the
+
B signal and the
microcontroller.
The value of the limiting resistance should be set so that when the
+
B signal is applied, the input current to
the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the
+
B input
potential may pass through the protective diode and increase the potential at the V
CC
pin, and this may affect
other devices.
Note that if a
+
B signal is input when the microcontroller power supply is off (not fixed at 0 V) , the power
supply is provided from the pins, so that incomplete operation may result.
Note that if the
+
B input is applied during power-on, the power supply is provided from the pins and the
resulting power supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the
+
B input pin open.
Note that analog system input/output pins (LCD drive pins, comparator input pins, etc.) cannot accept
+
B
signal input.
Sample recommended circuits :
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
P-ch
N-ch
V
CC
R
+
B input (0 V to 16 V)
Limiting
resistance
Protective diode
Input/Output equivalent circuits
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F927PFV-GE1 | 16-bit Microcontrolle |
| MB90F927S | 16-bit Microcontrolle |
| MB90F927SPF-GE1 | 16-bit Microcontrolle |
| MB90F927SPFV-GE1 | 16-bit Microcontrolle |
| MB90945 | 16-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F947APFR-GS-SPE1 | 制造商:FUJITSU 功能描述: |
| MB90F962SPMCR-GE1 | 制造商:FUJITSU 功能描述:IC MCU 16BIT 16LX 48LQFP |
| MB90F962SPMCR-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB90V340A-102CR | 制造商:FUJITSU 功能描述: |
| MB-910 | 制造商:Circuit Test 功能描述:BREADBOARD WIRING KIT - 350 PCS |
發(fā)布緊急采購，3分鐘左右您將得到回復。