- 您現在的位置：買賣IC網 > PDF目錄377921 > MB90F867AS (Fujitsu Limited) 16-bit Proprietary Microcontroller CMOS PDF資料下載
參數資料
| 型號： | MB90F867AS |
| 廠商： | Fujitsu Limited |
| 英文描述： | 16-bit Proprietary Microcontroller CMOS |
| 中文描述： | 16位微控制器專有的CMOS |
| 文件頁數： | 10/62頁 |
| 文件大?。?/td> | 412K |
| 代理商： | MB90F867AS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
MB90860A Series
10
(Continued)
Pin No.
Pin name
Circuit
type
Function
LQFP100*
2
QFP100*
1
4
6
P31
G
General purpose I/O.The register can be set to select whether to
use a pull-up resistor.This function is enabled in single-chip
mode.
Read strobe output pin for the data bus. This function is enabled
when the external bus is enabled.
Data sample input pin for input capture ICU5
General purpose I/O. The register can be set to select whether to
use a pull-up resistor. This function is enabled either in single-chip
mode or with the WR/WRL pin output disabled.
Write strobe output pin for the data bus. This function is enabled
when both the external bus and the WR/WRL pin output are en-
abled. WRL is used to write-strobe 8 lower bits of the data bus in
16-bit access while WR is used to write-strobe 8 bits of the data
bus in 8-bit access.
RX input pin for CAN2 Interface (MB90V340 only)
Sub external interrupt request input pin for INT10
General purpose I/O. The register can be set to select whether to
use a pull-up resistor.This function is enabled either in single-chip
mode or with the WRH pin output disabled.
Write strobe output pin for the 8 higher bits of the data bus. This
function is enabled when the external bus is enabled, when the
external bus 16-bit mode is selected, and when the WRH output
pin is enabled.
TX Output pin for CAN2 (MB90V340 only)
General purpose I/O. The register can be set to select whether to
use a pull-up resistor. This function is enabled either in single-chip
mode or with the hold function disabled.
Hold request input pin. This function is enabled when both the ex-
ternal bus and the hold function are enabled.
Waveform output pin for output compare OCU4
General purpose I/O. The register can be set to select whether to
use a pull-up resistor. This function is enabled either in single-chip
mode or with the hold function disabled.
Hold acknowledge output pin. This function is enabled when both
the external bus and the hold function are enabled.
Waveform output pin for output compare OCU5
General purpose I/O. The register can be set to select whether to
use a pull-up resistor. This function is enabled either in single-chip
mode or with the external ready function disabled.
Ready input pin. This function is enabled when both the
external bus and the external ready function are enabled.
Waveform output pin for output compare OCU6
RD
IN5
5
7
P32
G
WRL / WR
RX2
INT10R
6
8
P33
G
WRH
TX2
7
9
P34
G
HRQ
OUT4
8
10
P35
G
HAK
OUT5
9
11
P36
G
RDY
OUT6
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F867ASPFV | 16-bit Proprietary Microcontroller CMOS |
| MB90V340 | 16-bit Proprietary Microcontroller CMOS |
| MB90860E | 16-bit Proprietary Microcontroller |
| MB90867E | 16-bit Proprietary Microcontroller CMOS |
| MB90867EPF | 16-bit Proprietary Microcontroller CMOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F867ASPF-GE1 | 制造商:FUJITSU 功能描述:IC 16BIT MCU I2C SMD QFP100 |
| MB90F867ASPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F867ASPFR-G-SPE1 | 制造商:FUJITSU 功能描述: |
| MB90F897PMCR-G-TE1 | 制造商:FUJITSU 功能描述: |
| MB90F897PMT-GSE1 | 制造商:FUJITSU 功能描述:IC 16BIT MCU CAN 5V SMD LQFP48 |
發布緊急采購，3分鐘左右您將得到回復。