- 您現在的位置：買賣IC網 > PDF目錄377926 > MB90F549PFV (FUJITSU LTD) 16-bit Proprietary Microcontroller PDF資料下載
參數資料
| 型號： | MB90F549PFV |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-bit Proprietary Microcontroller |
| 中文描述： | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | PLASTIC, LQFP-100 |
| 文件頁數： | 16/56頁 |
| 文件大?。?/td> | 757K |
| 代理商： | MB90F549PFV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
MB90540/545 Series
16
(6) Pull-up/down resistors
The MB90540/545 Series does not support internal pull-up/down resistors (except Port0 - Port3:pull-up resis-
tors). Use external components where needed.
(7) Crystal Oscillator Circuit
Noises around X0 or X1 pins may be possible causes of abnormal operations. Make sure to provide bypass
capacitors via the shortest distances from X0, X1 pins, crystal oscillator (or ceramic resonator) and ground lines,
and make sure, to the utmost effort, that lines of oscillation circuits do not cross the lines of other circuits.
It is highly recommended to provide a printed circuit board artwork surrounding X0 and X1 pins with a grand
area for stabilizing the operation.
(8) Turning-on Sequence of Power Supply to A/D Converter and Analog Inputs
Make sure to turn on the A/D converter power supply (AV
CC
, AVRH, AVRL) and analog inputs (AN0 to AN7) after
turning-on the digital power supply (V
CC
).
Turn-off the digital power after turning off the A/D converter supply and analog inputs. In this case, make sure
that the voltage does not exceed AVRH or AV
CC
(turning on/off the analog and digital power supplies simulta-
neously is acceptable).
(9) Connection of Unused Pins of A/D Converter
Connect unused pins of A/D converter to AV
CC
= V
CC
, AV
SS
= AVRH = V
SS
.
(10) N.C. Pin
The N.C. (internally connected) pin must be opened for use.
(11) Notes on Energization
To prevent the internal regulator circuit from malfunctioning, set the voltage rise time during energization at
50
μ
s or more (0.2 V to 2.7 V).
(12) Indeterminate outputs from ports 0 and 1
The outputs from 0 and 1 become indeterminate during a power-on reset after the power is turned on.
Pay attention to the port output timing shown as follows.
Oscillation setting time
2
Step-down circuit
setting time
1
Vcc(power-supply pin)
PONR(power-on reset) signal
RST(external asynchronous reset) signal
RST(internal reset) signal
Oscillation clock signal
KA(internal operation clock A) signal
KB(internal operation clock B) signal
PORT(port output)signal
Indereterminate period
* :1:Step-down circuit setting time : 2
17
/oscillation clock frequency (oscillation clock frequency of 16 MHz: 8.19 ms)
* :2:Oscillation setting time: 2
18
/oscillation clock frequency (oscillation cllock frequency of 16 MHz: 16.38 ms)
Timming chart of indeterminate outputs from ports o and 1
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F553A | Octal Bus Transceivers And Registers With 3-State Outputs 24-CFP -55 to 125 |
| MB90T552A | 122 x 32 pixel format, Compact LCD size |
| MB90T552APF | 122 x 32 pixel format, Compact LCD size |
| MB90V550A | 16-bit Proprietary Microcontroller |
| MB90T552APFV | 16-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F562BPMC-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F562PMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F568PMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F583BPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F583BPMC-GE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。