參數資料
型號： MB90F428GCPF
廠商： FUJITSU LTD
元件分類： 微控制器/微處理器
英文描述： 16-Bit Original Microcontroller
中文描述： 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100
封裝： 14 X 20 MM, 3.35 MM HEIGHT, 0.65 MM PITCH, PLASTIC, QFP-100
文件頁數： 62/84頁
文件大?。?/td> 501K
代理商： MB90F428GCPF
MB90420G/425G Series
62
(Continued)
*6 : Average total output current is defined as the value of the average current flowing over 100 ms at all of the
corresponding pins. The “average value” can be calculated from the formula of “operating current” times
“ operating factor”.
*7 :
Applicable to pins : P00 to P07, P10 to P15, P50 to P57, P70 to P77, P80 to P87
Use within recommended operating conditions.
Use at DC voltage (current) .
The
+
B signal should always be applied with a limiting resistance placed between the
+
B signal and the
microcontroller.
The value of the limiting resistance should be set so that when the
+
B signal is applied the input current to
the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the
+
B input
potential may pass through the protective diode and increase the potential at the V
CC
pin, and this may affect
other devices.
Note that if a
+
B signal is input when the microcontroller current is off (not fixed at 0 V) , the power supply
is provided from the pins, so that incomplete operation may result.
Note that if the
+
B input is applied during power-on, the power supply is provided from the pins and the
resulting supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the
+
B input pin open.
Note that analog system input/output pins (LCD drive pins, comparator input pins, etc.) cannot accept
+
B
signal input.
Sample recommended circuits :
WARNING:
Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
P-ch
N-ch
V
CC
R
+
B input (0 V to 16 V)
Limiting
resistance
Protective diode
Input/Output equivalent circuits
相關PDF資料
PDF描述
MB90F428GCPFV 16-Bit Original Microcontroller
MB90435 Octal D-type Transparent Latches With 3-State Outputs 20-CDIP -55 to 125
MB90439SPFV 16-bit Proprietary Microcontroller
MB90F438L 16-bit Proprietary Microcontroller
MB90F438LPF 16-bit Proprietary Microcontroller
相關代理商/技術參數
參數描述
MB90F428GCPFR-GSE1 制造商:FUJITSU 功能描述:
MB90F438LSPFR-GE1 制造商:FUJITSU 功能描述:
MB90F438LSPMCR-GE1 制造商:FUJITSU 功能描述:
MB90F439PMCR-GE1 制造商:FUJITSU 功能描述:
MB90F439SPFR-GE1 制造商:FUJITSU 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*