- 您現在的位置：買賣IC網 > PDF目錄377916 > MB90F428G (Fujitsu Limited) Octal Transparent D-type Latches With 3-State Outputs 20-LCCC -55 to 125 PDF資料下載
參數資料
| 型號： | MB90F428G |
| 廠商： | Fujitsu Limited |
| 英文描述： | Octal Transparent D-type Latches With 3-State Outputs 20-LCCC -55 to 125 |
| 中文描述： | 16位微控制器原件 |
| 文件頁數： | 14/99頁 |
| 文件大?。?/td> | 1706K |
| 代理商： | MB90F428G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
MB90420G/5G (A) Series
14
Use of external clock signals
Even when an external clock is used, a stabilization period is required following a power-on reset or release
from sub clock mode or stop mode. Also, when an external clock is used it should drive only the X0 pin and the
X1 pin should be left open, as shown in Figure 3.
Power supply pins
Devices are designed to prevent problems such as latchup when multiple V
CC
and V
SS
supply pins are used, by
providing internal connections between pins having the same potential. However, in order to reduce unwanted
radiation, and to prevent abnormal operation of strobe signals due to rise in ground level, and to maintain total
output current ratings, all such pins should always be connected externally to power supplies and ground.
As shown in Figure 4, all V
CC
power supply pins must have the same potential. All V
SS
power supply pins should
be handled in the same way. If there are multiple V
CC
or V
SS
systems, the device will not operate properly even
within the warranted operating range.
In addition, care must be given to connecting the V
CC
and V
SS
pins of this device to a current source with as little
impedance as possible. It is recommended that a bypass capacitor of 1.0
μ
F be connected between V
CC
and
V
SS
as close to the pins as possible.
Proper sequence of A/D converter power supply analog input
A/D converter power (AV
CC
, AVRH) and analog input (AN0-AN7) must be applied after the digital power supply
(V
CC
) is switched on. When power is shut off, the A/D converter power supply and analog input must be cut off
before the digital power supply is switched on (V
CC
) . In both power-on and shut-off, care should be taken that
AVRH does not exceed AV
CC
. Even when pins which double as analog input pins are used as input ports, be
sure that the input voltage does not exceed AV
CC
. (There is no problem if analog power supplies and digital
power supplies are turned off and on at the same time.)
X0
X1
OPEN
MB90420G/425G (A) Series
Sample external clock connection
V
CC
V
SS
V
CC
V
CC
V
CC
V
CC
V
SS
V
SS
V
SS
V
SS
Power supply input pins (V
CC
/V
SS
)
相關PDF資料 |
PDF描述 |
|---|---|
| MB90427G | 16-Bit Original Microcontroller |
| MB90428G | Octal D-type Transparent Latches With 3-State Outputs 20-LCCC -55 to 125 |
| MB90F428GA | 16-Bit Original Microcontroller |
| MB90428GA | 16-Bit Original Microcontroller |
| MB90F428GAPF | 16-Bit Original Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F428GAPMC-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F428GCPFR-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F438LSPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F438LSPMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F439PMCR-GE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。