- 您現在的位置：買賣IC網 > PDF目錄377925 > MB90F378 (Fujitsu Limited) 16-bit Proprietary Microcontroller PDF資料下載
參數資料
| 型號： | MB90F378 |
| 廠商： | Fujitsu Limited |
| 英文描述： | 16-bit Proprietary Microcontroller |
| 中文描述： | 16位微控制器專有 |
| 文件頁數： | 16/65頁 |
| 文件大小： | 323K |
| 代理商： | MB90F378 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
MB90378 Series
16
■
HANDLING DEVICES
1.
Be sure that the maximum rated voltage is not exceeded (latch-up prevention).
A latch-up may occur on a CMOS IC if a voltage higher than V
CC
or lower than V
SS
is applied to an input or output
pin other than medium-to-high voltage pins. A latch-up may also occur if a voltage higher than the rating is
applied between V
CC
pin and V
SS
pin. A latch-up causes a rapid increase in the power supply current, which can
result in thermal damage to an element. Take utmost care that the maximum rated voltage is not exceeded.
When turning the power on or off to analog circuits, be sure that the analog supply voltages (AV
CC
, AVR) and
analog input voltage do not exceed the digital supply voltage (V
CC
).
2.
Stabilize the supply voltages
Even within the operation guarantee range of the V
CC
supply voltage, a malfunction can be caused if the supply
voltage undergoes a rapid change. For voltage stabilization guidelines, the V
CC
ripple fluctuations (P-P value)
at commercial frequencies (50 Hz to 60 Hz) should be suppressed to "10%" or less of the reference V
CC
value.
During a momentary change such as when switching a supply voltage, voltage fluctuations should also be
suppressed so that the "transient fluctuation rate" is 0.1 V/ms or less.
3.
Power-on
To prevent a malfunction in the built-in voltage drop circuit, secure "50
μ
s (between 0.2 V and 1.8 V)" or more
for the voltage rise time during power-on.
4.
Treatment of unused input pins
An unused input pin may cause a malfunction if it is left open. Every unused input pin should be pulled up or down.
5.
Treatment of A/D converter, and D/A converter power pin
When the A/D converter, D/A converter and comparator is not used, connect the pins as follows: AV
CC
=
V
CC
,
AV
SS
=
AVR
=
V
SS
.
6.
Notes on external clock
When an external clock is used, the oscillation stabilization wait time is required at power-on reset or at cancel-
lation of sub-clock mode or stop mode. As shown in diagram below, when an external clock is used, connect
only the X0 pin and leave the X1 pin open.
Open
X1
X0
MB90378 series
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F378PFF-GE1 | 16-bit Proprietary Microcontroller |
| MB90F387 | 16-bit Proprietary Microcontroller CMOS |
| MB90F387PMT | 16-bit Proprietary Microcontroller CMOS |
| MB90F387S | 16-bit Proprietary Microcontroller CMOS |
| MB90F387SPMT | 16-bit Proprietary Microcontroller CMOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F387PMCR-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F387PMT-GSE1 | 功能描述:IC MCU FLASH 64K ROM 48LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:F²MC MB90385 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM |
| MB90F387SPMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F387SPMCR-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB90F387SPMCRGSE1 | 制造商:FUJITSU 功能描述:Pb Free |
發布緊急采購，3分鐘左右您將得到回復。