- 您現在的位置：買賣IC網 > PDF目錄377925 > MB90F367S (Fujitsu Limited) 16-bit Proprietary Microcontroller PDF資料下載
參數資料
| 型號： | MB90F367S |
| 廠商： | Fujitsu Limited |
| 英文描述： | 16-bit Proprietary Microcontroller |
| 中文描述： | 16位微控制器專有 |
| 文件頁數： | 38/59頁 |
| 文件大?。?/td> | 262K |
| 代理商： | MB90F367S |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
MB90360 Series
38
(Continued)
*1 : This parameter is based on V
SS
=
AV
SS
=
0 V.
*2 : Set AV
CC
and V
CC
to the same voltage. Make sure that AV
CC
does not exceed V
CC
and that the voltage at the
analog inputs does not exceed AV
CC
when the power is switched on.
*3 : V
I
and V
O
should not exceed V
CC
+
0.3 V. V
I
should not exceed the specified ratings. However, if the maximun
current to/from an input is limited by some means with external components, the I
CLAMP
rating supersedes the
V
I
rating.
*4 : Applicable to pins : P24 to P27, P40 to P44, P50 to P57, P60 to P67, P80, P82 to P87
*5 : Applicable to pins : P20 to P23
*6 : Applicable to pins : P20 to P27, P40 to P44, P50 to P57, P60 to P67, P80, P82 to P87
Use within recommended operating conditions.
Use at DC voltage (current) .
The
+
B signal should always be applied a limiting resistance placed between the
+
B signal and the
microcontroller.
The value of the limiting resistance should be set so that when the
+
B signal is applied the input current to
the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the
+
B input
potential may pass through the protective diode and increase the potential at the V
CC
pin, and this may affect
other devices.
Note that if a
+
B signal is inputted when the microcontroller power supply is off (not fixed at 0 V) , the power
supply is provided from the pins, so that incomplete operation may result.
Note that if the
+
B input is applied during power-on, the power supply is provided from the pins and the
resulting power supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the
+
B input pin open.
Sample recommended circuits :
Input/output equivalent circuits
*7 : If used exceeding T
A
=
+
105
°
C, please contact Fujitsu for reliability limitations.
WARNING:
Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
Pch
Nch
V
CC
R
+
B input (0 V to 16 V)
Limiting
resistance
Protective diode
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F367SPMT | 16-bit Proprietary Microcontroller |
| MB90F367T | 16-bit Proprietary Microcontroller |
| MB90F367TPMT | 16-bit Proprietary Microcontroller |
| MB90F367TS | 16-bit Proprietary Microcontroller |
| MB90F367TSPMT | 16-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F367TPMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F367TPMCR-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB90F367TPMCR-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F367TSPMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F367TSPMCR-GSE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。