參數資料
型號： MB90F362SPMT
廠商： Fujitsu Limited
英文描述： 16-bit Proprietary Microcontroller
中文描述： 16位微控制器專有
文件頁數： 14/59頁
文件大?。?/td> 262K
代理商： MB90F362SPMT
MB90360 Series
14
4.
Precautions for when not using a sub-clock signal
If you do not connect pins X0A and X1A to an oscillator, use pull-down handling on the X0A pin and leave the
X1A pin open.
5.
Notes on during operation of PLL clock mode
If the PLL clock mode is selected, the microcontroller attempts to be working with the self-oscillating circuit even
when there is no external oscillator or external clock input is stopped. Performance of this operation, however,
cannot be guaranteed.
6.
Power supply pins (V
CC
/V
SS
)
If there are multiple V
CC
and V
SS
pins, from the point of view of device design, pins to be of the same potential
are connected the inside of the device to prevent such malfunctioning as latch up.
To reduce unnecessary radiation, prevent malfunctioning of the strobe signal due to the rise of ground level,
and observe the standard for total output current, be sure to connect the V
CC
and V
SS
pins to the power supply
and ground externally.
Connect V
CC
and V
SS
to the device from the current supply source at a low impedance.
As a measure against power supply noise, connect a capacitor of about 0.1
μ
F as a bypass capacitor between
V
CC
and V
SS
in the vicinity of V
CC
and V
SS
pins of the device.
7.
Pull-up/down resistors
The MB90360 Series does not support internal pull-up/down resistors (Port 2 : built-in pull-up resistors) . Use
external components where needed.
8.
Crystal oscillator circuit
Noises around X0 or X1 pin may be possible causes of abnormal operations. Make sure to provide bypass
capacitors via shortest distance from X0, X1 pins, crystal oscillator (or ceramic resonator) and ground lines, and
make sure, to the utmost effort, that lines of oscillation circuit do not cross the lines of other circuits.
It is highly recommended to provide a printed circuit board artwork surrounding X0 and X1 pins with a ground
area for stabilizing the operation.
9.
Turning-on sequence of power supply to A/D converter and analog inputs
Make sure to turn on the A/D converter power supply (AV
CC
and AVR) and analog inputs (AN0 to AN15) after
turning-on the digital power supply (V
CC
) .
Turn-off the digital power after turning off the A/D converter power supply and analog inputs. In this case, make
sure that the voltage does not exceed AVRH or AV
CC
(turning on/off the analog and digital power supplies
simultaneously is acceptable) .
V
CC
V
SS
V
CC
V
CC
V
CC
V
CC
V
SS
V
SS
V
SS
V
SS
MB90360
Series
相關PDF資料
PDF描述
MB90F362T 16-bit Proprietary Microcontroller
MB90F362TPMT 16-bit Proprietary Microcontroller
MB90F362TS 16-bit Proprietary Microcontroller
MB90F362TSPMT 16-bit Proprietary Microcontroller
MB90F367 16-bit Proprietary Microcontroller
相關代理商/技術參數
參數描述
MB90F362TESPMCRGE1 制造商:FUJI 功能描述:Pb Free
MB90F362TESPMCR-GE1 制造商:FUJITSU 功能描述:MCU 16BIT 16LX 64K FLASH 48LQFP 制造商:FUJITSU 功能描述:MCU, 16BIT, 16LX, 64K FLASH, 48LQFP, Controller Family/Series:F2MC-16LX, Core Si
MB90F362TESPMCR-G-JNE1 制造商:FUJITSU 功能描述:
MB90F362TESPMCR-GN9E1 功能描述:IC MCU 16BIT 制造商:cypress semiconductor corp 系列:F2MC-16LX MB90360E 零件狀態:在售 核心處理器:F2MC-16LX 核心尺寸:16-位 速度:24MHz 連接性:CAN，LIN，UART/USART 外設:DMA，POR，WDT I/O 數:36 程序存儲容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 容量:- RAM 容量:3K x 8 電壓 - 電源（Vcc/Vdd）:3 V ~ 5.5 V 數據轉換器:A/D 16x8/10b 振蕩器類型:外部 工作溫度:-40°C ~ 105°C（TA） 標準包裝:250
MB90F367TPMCR-GE1 制造商:FUJITSU 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*