- 您現在的位置：買賣IC網 > PDF目錄377924 > MB90F356TEPMC1 (FUJITSU LTD) 16-bit Proprietary Microcontrollers PDF資料下載
參數資料
| 型號： | MB90F356TEPMC1 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-bit Proprietary Microcontrollers |
| 中文描述： | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 10 X 10 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 52/85頁 |
| 文件大?。?/td> | 880K |
| 代理商： | MB90F356TEPMC1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
MB90350E Series
52
(Continued)
*1:This parameter is based on V
SS
=
AV
SS
=
0 V
*2:Set AV
CC
and V
CC
to the same voltage. Make sure that AV
CC
does not exceed V
CC
and that the voltage at the
analog inputs does not exceed AV
CC
when the power is switched on.
*3:V
I
and V
O
should not exceed V
CC
+
0.3 V. V
I
should not exceed the specified ratings. However if the maximum
current to/from an input is limited by some means with external components, the I
CLAMP
rating supersedes the
V
I
rating.
*4:Applicable to pins: P00 to P07, P10 to P17, P20 to P25, P30 to P37, P40 to P45, P50 to P56, P60 to P67
*5:
Applicable to pins: P00 to P07, P10 to P17, P20 to P25, P30 to P37, P40 to P45,
P50 to P56 (for evaluation device : P50 to P55) , P60 to P67
Use within recommended operating conditions.
Use at DC voltage (current)
The
+
B signal should always be applied a connecting limit resistance between the
+
B signal and the
microcontroller.
The value of the limiting resistance should be set so that when the
+
B signal is applied the input current to
the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the
+
B input
potential may pass through the protective diode and increase the potential at the V
CC
pin, and this may affect
other devices.
Note that if a
+
B signal is input when the microcontroller power supply is off (not fixed at 0 V) , the power
supply is provided from the pins, so that incomplete operation may result.
Note that if the
+
B input is applied during power-on, the power supply is provided from the pins and the resulting
power supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the
+
B input pin open.
Recommended circuit sample:
*6 : If used exceeding T
A
=
+
105
°
C, be sure to contact Fujitsu for reliability limitations.
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
P-ch
N-ch
V
CC
R
Input/output equivalent circuits
+
B input (0 V to 16 V)
Limiting
resistance
Protective diode
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F356TESPMC | 16-bit Proprietary Microcontrollers |
| MB90F356TESPMC1 | 16-bit Proprietary Microcontrollers |
| MB90F357E | 16-bit Proprietary Microcontrollers |
| MB90F351EPMC | 16-bit Proprietary Microcontrollers |
| MB90F357EPMC | 16-bit Proprietary Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F362ESPMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F362ESPMCR-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB90F362TESPMCRGE1 | 制造商:FUJI 功能描述:Pb Free |
| MB90F362TESPMCR-GE1 | 制造商:FUJITSU 功能描述:MCU 16BIT 16LX 64K FLASH 48LQFP 制造商:FUJITSU 功能描述:MCU, 16BIT, 16LX, 64K FLASH, 48LQFP, Controller Family/Series:F2MC-16LX, Core Si |
| MB90F362TESPMCR-G-JNE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。