- 您現(xiàn)在的位置：買賣IC網 > PDF目錄377929 > MB90882PF (FUJITSU LTD) 16-Bit Proprietary Microcontroller PDF資料下載
參數資料
| 型號： | MB90882PF |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-Bit Proprietary Microcontroller |
| 中文描述： | 16-BIT, MROM, 33 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, 3.35 MM HEIGHT, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件頁數： | 42/75頁 |
| 文件大?。?/td> | 1083K |
| 代理商： | MB90882PF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁
MB90880 Series
42
(Continued)
*5 : The average output current is defined as the value of the average current flowing over 100 ms at any one of
the corresponding pins.
*6 : The average total output current is defined as the value of the average current flowing over 100 ms at all of the
corresponding pins.
*7 :
Relevant pins : P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67,
P70 to P76, P80 to P87, P90 to P97, PA0 to PA3
Use within recommended operating conditions.
Use with DC voltage (current) .
The
+
B signal should always be applied with a limiting resistance placed between the
+
B signal and the
microcontroller.
Set the limiting resistor value, whether instantaneous or stationary, so that the current to be input to the
microcontroller pin does not exceed the rating during the input of the
+
B signal.
Note that when the microcontroller drive current is low, such as in the power saving modes, the
+
B input
potential may pass through the protective diode and increase the potential at the VCC pin, and this may
affect other devices.
Note that if a
+
B signal is input when the microcontroller current is off (not fixed at 0 V) , the power supply
is provided from the pins, so that incomplete operation may result.
Note that if the
+
B input is applied during power-on, the power supply is provided from the pins and the
resulting supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the
+
B input pin open.
Note that analog system input/output pins (LCD drive pins, comparator input pins, etc.) cannot accept
+
B
signal input.
Sample recommended circuit :
*8 : P74 to P76 and P80 to P87 can be used as 5V I/F pins.
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed any of these ratings.
P-ch
N-ch
V
CC
R
Input/Output equivalent circuit
Protective diode
Limiting
resistance
+
B input (0V to 16V)
相關PDF資料 |
PDF描述 |
|---|---|
| MB90882PMC | 16-Bit Proprietary Microcontroller |
| MB90882S | 16-Bit Proprietary Microcontroller |
| MB90882SPF | 16-Bit Proprietary Microcontroller |
| MB90882SPMC | 16-Bit Proprietary Microcontroller |
| MB90883 | 16-Bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90882PMC | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90882S | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90882SPF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90882SPMC | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90883 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
發(fā)布緊急采購，3分鐘左右您將得到回復。