- 您現在的位置：買賣IC網 > PDF目錄377921 > MB90867ESPFV (FUJITSU LTD) 16-bit Proprietary Microcontroller CMOS PDF資料下載
參數資料
| 型號： | MB90867ESPFV |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-bit Proprietary Microcontroller CMOS |
| 中文描述： | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 14 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-100 |
| 文件頁數： | 21/67頁 |
| 文件大?。?/td> | 980K |
| 代理商： | MB90867ESPFV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
MB90860E Series
21
■
HANDLING DEVICES
1.
Preventing latch-up
CMOS IC may suffer latch-up under the following conditions :
A voltage higher than V
CC
or lower than V
SS
is applied to an input or output pin.
A voltage higher than the rated voltage is applied between V
CC
and V
SS
pins.
The AV
CC
power supply is applied before the V
CC
voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
For the same reason, also be careful not to let the analog power-supply voltage (AV
CC
, AVRH) exceed the digital
power-supply voltage.
Handling unused pins
2.
Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the
device. Therefore they must be pulled up or pulled down through resistors. In this case those resistors should
be more than 2 k
.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
Power supply pins (V
CC
/V
SS
)
If there are multiple V
CC
and V
SS
pins, from the point of view of device design, pins to be of the same potential
are connected the inside of the device to prevent such malfunctioning as latch up.
To reduce unnecessary radiation, prevent malfunctioning of the strobe signal due to the rise of ground level,
and observe the standard for total output current, be sure to connect the V
CC
and V
SS
pins to the power supply
and ground externally.
Connect V
CC
and V
SS
to the device from the current supply source at a low impedance.
As a measure against power supply noise, connect a capacitor of about 0.1
μ
F as a bypass capacitor between
V
CC
and V
SS
in the vicinity of V
CC
and V
SS
pins of the device
3.
4.
Mode Pin (MD0 to MD2)
Connect the mode pin directly to V
CC
or V
SS
pins.
To prevent the device unintentionally entering test mode due to noise, lay out the printed circuit board so as to
minimize the distance from the mode pins to V
CC
or V
SS
pins and to provide a low-impedance connection.
Vcc
Vss
Vss
Vcc
Vss
Vcc
MB90860E
Series
Vcc
Vss
Vcc
Vss
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F867E | 16-bit Proprietary Microcontroller CMOS |
| MB90F867EPF | 16-bit Proprietary Microcontroller CMOS |
| MB90F867EPFV | 16-bit Proprietary Microcontroller CMOS |
| MB90F867ES | 16-bit Proprietary Microcontroller CMOS |
| MB90F867ESPF | 16-bit Proprietary Microcontroller CMOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90880 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90882 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90882PF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90882PMC | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90882S | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。