- 您現在的位置：買賣IC網 > PDF目錄377921 > MB90867ASPF (FUJITSU LTD) 16-bit general-purpose microcontroller PDF資料下載
參數資料
| 型號： | MB90867ASPF |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-bit general-purpose microcontroller |
| 中文描述： | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | PLASTIC, QFP-100 |
| 文件頁數： | 19/62頁 |
| 文件大?。?/td> | 412K |
| 代理商： | MB90867ASPF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
MB90860A Series
19
5.
Notes on during operation of PLL clock mode
If the PLL clock mode is selected, the microcontroller attempt to be working with the self-oscillating circuit even
when there is no external oscillator or external clock input is stopped. Performance of this operation, however,
cannot be guaranteed.
Power supply pins (V
CC
/V
SS
)
If there are multiple V
CC
and V
SS
pins, from the point of view of device design, pins to be of the same potential
are connected the inside of the device to prevent such malfunctioning as latch up.
To reduce unnecessary radiation, prevent malfunctioning of the strobe signal due to the rise of ground level,
and observe the standard for total output current, be sure to connect the V
CC
and V
SS
pins to the power supply
and ground externally.
Connect V
CC
and V
SS
to the device from the current supply source at a low impedance.
As a measure against power supply noise, connect a capacitor of about 0.1
μ
F as a bypass capacitor between
V
CC
and V
SS
in the vicinity of V
CC
and V
SS
pins of the device
6.
7.
Pull-up/down resistors
The MB90860A Series does not support internal pull-up/down resistors (Port 0 to Port 3: built-in pull-up resistors).
Use external components where needed.
Crystal Oscillator Circuit
8.
Noises around X0 or X1 pins may be possible causes of abnormal operations. Make sure to provide bypass
capacitors via shortest distance from X0, X1 pins, crystal oscillator (or ceramic resonator) and ground lines, and
make sure, to the utmost effort, that lines of oscillation circuit not cross the lines of other circuits.
It is highly recommended to provide a printed circuit board art work surrounding X0 and X1 pins with a ground
area for stabilizing the operation.
Turning-on Sequence of Power Supply to A/D Converter and Analog Inputs
9.
Make sure to turn on the A/D converter power supply (AV
CC
, AVRH, AVRL) and analog inputs (AN0 to AN23)
after turning-on the digital power supply (V
CC
) .
Turn-off the digital power after turning off the A/D converter supply and analog inputs. In this case, make sure
that the voltage not exceed AVRH or AV
CC
(turning on/off the analog and digital power supplies simultaneously
is acceptable) .
10. Connection of Unused Pins of A/D Converter if A/D Converter is used
Connect unused pins of A/D converter to AV
CC
=
V
CC
, AV
SS
=
AVRH
=
AVRL
=
V
SS
.
Vcc
Vss
Vss
Vcc
Vss
Vcc
MB90860A
Series
Vcc
Vss
Vcc
Vss
相關PDF資料 |
PDF描述 |
|---|---|
| MB90867ASPFV | 16-bit general-purpose microcontroller |
| MB90F867APF | 16-bit general-purpose microcontroller |
| MB90F867APFV | 16-bit general-purpose microcontroller |
| MB90F867ASPF | 16-bit general-purpose microcontroller |
| MB90867AS | 16-bit Proprietary Microcontroller CMOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90867ASPFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit general-purpose microcontroller |
| MB90867E | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90867EPF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90867EPFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90867ES | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。