- 您現在的位置：買賣IC網 > PDF目錄377920 > MB90663AP-SH (FUJITSU LTD) 16-bit Proprietary Microcontroller PDF資料下載
參數資料
| 型號： | MB90663AP-SH |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-bit Proprietary Microcontroller |
| 中文描述： | 16-BIT, MROM, 32 MHz, MICROCONTROLLER, PDIP64 |
| 封裝： | SHRINK, PLASTIC, DIP-64 |
| 文件頁數： | 12/84頁 |
| 文件大小： | 1440K |
| 代理商： | MB90663AP-SH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
12
MB90660A Series
I
HANDLING DEVICES
1. Preventing Latchup
Latchup may occur with CMOS ICs if voltage higher than V
CC
or lower than V
SS
is applied to input and output
pins other than medium- to high-voltage pins or if higher than the voltage which shows on “1. Absolute Maximum
Ratings” in section “
I
Electrical Characteristics” is applied between V
CC
and V
SS
.
When latchup occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
To prevent the similar aftereffects, use also the utmost care not to allow the analog supply voltage to exceed the
digital supply voltage.
2. Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions. They should be pins should be connected to a pull-
up or pull-down resistor.
3. External Reset Input
When resetting by inputting “L” level to the RST pin, the “L” level must be input for at least 5 machine cycles to
ensure that internal reset has occurred. Be aware of this point when using external clock input.
4. V
CC
, V
SS
Pin
Be sure that both V
CC
and V
SS
are at the same voltage.
5. Notes on Using an External Clock
Drive X0 when using an external clock.
6. Order of Power-on to A/D Converter and Analog Inputs
Power-off (AV
CC
, AVR) to the digital power supply (V
CC
) must be performed only after the A/D converter and the
analog inputs (AN0 to AN7) has been turned on.
Turning on or off should always be performed keeping AVR below AV
CC
.
Use caution for the input voltage not to exceed AV
CC
when the pin sharing the analog input for its function is
used as an input port.
7. Programming Mode
When the MB90P663A is shipped from Fujitsu, all bits (48 K
×
8 bits) are set to “1”. Program by setting selected
bits to “0” when you wish to set the data. Note that “1” cannot be programming electrically.
X0
X1
MB90660A
Using an External Clock
相關PDF資料 |
PDF描述 |
|---|---|
| MB90662A | 16-Bit Proprietary Microcontroller(16位專用微控制器) |
| MB90660A | UL/CSA, T-BEAM, D-ON |
| MB90663A | 16-Bit Proprietary Microcontroller(16位專用微控制器) |
| MB90670 | Scan Test Devices With Octal Bus Transceivers And Registers 28-CDIP -55 to 125 |
| MB673XXX | AV CMOS SEREIS GATE ARRAYS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90670 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90671 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90671PF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90671PFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
| MB90672 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-Bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。