- 您現(xiàn)在的位置：買賣IC網 > PDF目錄377920 > MB90598GPF (FUJITSU LTD) 16-bit Proprietary Microcontroller PDF資料下載
參數資料
| 型號： | MB90598GPF |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-bit Proprietary Microcontroller |
| 中文描述： | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | PLASTIC, QFP-100 |
| 文件頁數： | 12/52頁 |
| 文件大?。?/td> | 295K |
| 代理商： | MB90598GPF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
MB90595/595G Series
12
I
HANDLING DEVICES
(1) Make Sure that the Voltage not Exceed the Maximum Rating (to Avoid a Latch-up).
In CMOS ICs, a latch-up phenomenon is caused when an voltage exceeding V
CC
or an voltage below V
SS
is
applied to input or output pins or a voltage exceeding the rating is applied across V
CC
and V
SS
.
When a latch-up is caused, the power supply current may be dramatically increased causing resultant thermal
break-down of devices. To avoid the latch-up, make sure that the voltage not exceed the maximum rating.
In turning on/turning off the analog power supply, make sure the analog power voltage (AV
CC
, AVRH, DV
CC
) and
analog input voltages not exceed the digital voltage (V
CC
).
(2) Treatment of Unused Pins
Unused input pins left open may cause abnormal operation, or latch-up leading to permanent damage. Unused
input pins should be pulled up or pulled down through at least 2 k
resistance.
Unused input/output pins may be left open in output state, but if such pins are in input state they should be
handled in the same way as input pins.
(3) Using external clock
In using the external clock, drive X0 pin only and leave X1 pin unconnected.
(4) Power supply pins (Vcc/Vss)
In products with multiple V
cc
or V
ss
pins, pins with the same potential are internally connected in the device to
avoid abnormal operations including latch-up. However, you must connect the pins to an external power and a
ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals caused
by the rise in the ground level, and to conform to the total current rating (See the figure below.)
Make sure to connect V
cc
and V
ss
pins via lowest impedance to power lines.
It is recommended to provide a bypass capacitor of around 0.1
μ
F between V
cc
and V
ss
pins near the device.
X0
X1
MB90595/595G Series
Using external clock
Open
Vcc
Vss
Vss
Vcc
Vss
Vcc
MB90595/595G
Series
Vcc
Vss
Vcc
Vss
相關PDF資料 |
PDF描述 |
|---|---|
| MB90598PF | 16-bit Proprietary Microcontroller |
| MB90F598GPF | 16-bit Proprietary Microcontroller |
| MB90F598PF | 16-bit Proprietary Microcontroller |
| MB90611APF | 16-bit Proprietary Microcontroller |
| MB90611APFV | 16-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90598PF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90611A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90611APF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90611APFR-G-BNDE1 | 制造商:FUJITSU 功能描述: |
| MB90611APFR-G-JNE1 | 制造商:FUJITSU 功能描述: |
發(fā)布緊急采購，3分鐘左右您將得到回復。