- 您現在的位置：買賣IC網 > PDF目錄45188 > MB90591GPF 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | MB90591GPF |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | PLASTIC, QFP-100 |
| 文件頁數： | 31/56頁 |
| 文件大小： | 697K |
| 代理商： | MB90591GPF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
MB90590/590G Series
37
*6 :
Applicable to pins : P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67,
P70 to P77, P80 to P87, P90 toP95
Use within recommended operating conditions.
Use at DC voltage (current)
The +B signal should always be applied with a limiting resistance placed between the +B signal and the
microcontroller.
The value of the limiting resistance should be set so that when the +B signal is applied the input current to
the microcontroller pins does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input
potential may pass through the protective diode and increase the potential at the VCC pin, and this may affect
other devices.
Note that if a +B signal is input when the microcontroller power supply is off (not fixed at 0 V) , the power supply is
provided from the pins, so that incomplete operation may result.
Note that if the +B input is applied during power-on, the power supply is provided from the pins and the resulting
supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the +B input pin open.
Note that analog system input/output pins other than the A/D input pins (LCD drive pins, comparator input pins,
etc.) cannot accept
+B signal input.
Sample recommended circuits
Note : Average output current = operating current
× operating efficiency
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
Input/Output equivalent circuits
P-ch
N-ch
VCC
R
+B input (0 V to 16 V)
Limiting
resistance
Protective diode
相關PDF資料 |
PDF描述 |
|---|---|
| MB90591PF | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB90613APF | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB90652APF | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP100 |
| MB90653APFV | 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP100 |
| MB90F654APFV | 16-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90591PF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90594 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90594G | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90594GPF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90594PF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。