- 您現(xiàn)在的位置：買賣IC網 > PDF目錄377927 > MB90562P (FUJITSU LTD) 16-bit Proprietary Microcontrollers PDF資料下載
參數資料
| 型號： | MB90562P |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-bit Proprietary Microcontrollers |
| 中文描述： | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PDIP64 |
| 封裝： | 1.788 MM PITCH, SHRINK, PLASTIC, DIP-64 |
| 文件頁數： | 16/91頁 |
| 文件大?。?/td> | 484K |
| 代理商： | MB90562P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁
MB90560/565 Series
16
Example of using an external clock
(7) Power supply pins
The multiple V
CC
and V
SS
pins are connected together in the internal device design so as to prevent misoperation
such as latch-up. However, always connect all V
CC
and V
SS
pins to the same potential externally to minimize
spurious radiation, prevent misoperation of strobe signals due to increases in the ground level, and maintain the
overall output current rating.
Also, ensure that the impedance of the V
CC
and V
SS
connections to the power supply is as low as possible.
To minimize these problems, connect a bypass capacitor of approximately 0.1
μ
F between V
CC
and V
SS
. Connect
the capacitor close to the V
CC
and V
SS
pins.
(8) Sequence for connecting and disconnecting power supply
Do not apply voltage to the A/D converter power supply pins (AV
CC
, AVR, AV
SS
) or analog inputs (AN0 to AN7)
until the digital power supply (V
CC
) is turned on. When turning the device off, turn off the digital power supply
after disconnecting the A/D converter power supply and analog inputs. When turning the power on or off, ensure
that AVR does not exceed AV
CC
.
When using the I/O ports that share pins with the analog inputs, ensure that the input voltage does not exceed
AV
CC
(turning the analog and digital power supplies on and off simultaneously is OK) .
(9) Conditions when output from ports 0 and 1 is undefined
After turning on the power supply, the outputs from ports 0 and 1 are undefined during the oscillation stabilization
delay time controlled by the regulator circuit (during the power-on reset) if the RST pin level is “H”. When the
RST pin level is “L”, ports 0 and 1 go to high impedance.
Figures 1 and 2 show the timing (for the MB90F562/B and MB90V560) .
Note that this undefined output period does not occur on products without an internal regulator circuit as these
products do not have an oscillation stabilization delay time.
(MB90561/A, MB90562/A, MB90F568, and MB90567/8)
X0
X1
OPEN
MB90560/565 series
相關PDF資料 |
PDF描述 |
|---|---|
| MB90562PF | 16-bit Proprietary Microcontrollers |
| MB90562PFM | 16-bit Proprietary Microcontrollers |
| MB90565 | 16-bit Proprietary Microcontrollers |
| MB90567PF | 16-bit Proprietary Microcontrollers |
| MB90567PFM | 16-bit Proprietary Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90562PF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontrollers |
| MB90562PFM | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontrollers |
| MB90562P-SH | 制造商:FUJITSU 功能描述: |
| MB90565 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontrollers |
| MB90565_08 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontrollers |
發(fā)布緊急采購，3分鐘左右您將得到回復。