- 您現在的位置：買賣IC網 > PDF目錄377927 > MB90553A (Fujitsu Limited) Triple 3-Input Positive-AND Gates 20-LCCC -55 to 125 PDF資料下載
參數資料
| 型號： | MB90553A |
| 廠商： | Fujitsu Limited |
| 英文描述： | Triple 3-Input Positive-AND Gates 20-LCCC -55 to 125 |
| 中文描述： | 16位微控制器專有 |
| 文件頁數： | 15/58頁 |
| 文件大小： | 695K |
| 代理商： | MB90553A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
MB90550A/550B Series
15
I
HANDLING DEVICES
1.
Preventing Latchup
CMOS ICs may cause latchup in the following situations:
When a voltage higher than Vcc or lower than Vss is applied to input or output pins.
When a voltage exceeding the rating is applied between Vcc and Vss.
When AVcc power is supplied prior to the Vcc voltage.
If latchup occurs, the power supply current increases rapidly, sometimes resulting in thermal breakdown of the
device. Use meticulous care not to let it occur.
For the same reason, also be careful not to let the analog power-supply voltage exceed the digital power-supply
voltage.
Handling unused input pins
2.
Leaving unused input pins open may cause a malfunction or latch-up which leads to fatal damage to the device.
Therefore they must be pulled up or pulled down through at least 2 k
resistance. Also, unused input/output
pins should be left open in output state or handled in the same way as unused input pins.
Notes on Using External Clock
3.
In using the external clock, drive X0 pin only and leave X1 pin unconnected.
4.
Power Supply Pins (V
CC
/V
SS
)
In products with multiple V
CC
or V
SS
pins, the pins of a same potential are internally connected in the device to
avoid abnormal operations including latch-up. However, the pins should be connected to external power and
ground lines to lower the electro-magnetic emission level and abnormal operation of strobe signals caused by
the rise in the ground level, and to conform to the total current rating.
Make sure to connect V
CC
and V
SS
pins via lowest impedance to power lines.
It is recommended that a bypass capacitor of around 0.1
μ
F be placed between the V
CC
and V
SS
pins near the
device.
Using external clock
MB90550A/550B series
X0
X1
Open
V
CC
V
SS
V
CC
V
CC
V
CC
V
CC
V
SS
V
SS
V
SS
V
SS
Using
power supply pins
MB90550A/550B
series
相關PDF資料 |
PDF描述 |
|---|---|
| MB90553APF | Triple 3-Input Positive-AND Gates 14-CDIP -55 to 125 |
| MB90553APFV | Triple 3-Input Positive-AND Gates 14-CFP -55 to 125 |
| MB90553B | Hex Schmitt-trigger Inverters 20-LCCC -55 to 125 |
| MB90553BPF | Hex Schmitt-trigger Inverters 14-CDIP -55 to 125 |
| MB90553BPFV | Hex Schmitt-trigger Inverters 14-CFP -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90553APF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90553APFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90553APMC | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90553B | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90553BPF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。