- 您現在的位置：買賣IC網 > PDF目錄377926 > MB90483CPFV (FUJITSU LTD) 16-bit Proprietary Microcontroller PDF資料下載
參數資料
| 型號： | MB90483CPFV |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-bit Proprietary Microcontroller |
| 中文描述： | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 14 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-100 |
| 文件頁數： | 17/120頁 |
| 文件大?。?/td> | 1241K |
| 代理商： | MB90483CPFV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
MB90480/485 Series
17
8.
Treatment of power supply pins on models with A/D converters
Even when the A/D converters are not in use, be sure to make the necessary connections AV
CC
=
AVRH
=
V
CC
,
and AV
SS
=
V
SS
.
9.
Notes on Using Power Supply
Only the MB90485 series usually uses a 3 V power supply. By setting V
CC
3
=
3 V power supply and V
CC
5
=
5 V
power supply, P20 to P27, P30 to P37, P40 to P47 and P70 to P77 can be interfaced as 5 V power supplies
separately from the main 3 V power supply. Note that the analog power supplies (such as AV
CC
and AV
SS
) for
the A/D converter can be used only as 3 V power supplies.
10. Notes on Using External Clock
Even when using an external clock signal, an oscillation stabilization delay is applied after a power-on reset or
when recovering from sub-clock or stop mode. When using an external clock, 25 MHz should be the upper
frequency limit.
The following figure shows a sample use of external clock signals.
11. Treatment of NC pins
NC (internally connected) pins should always be left open.
12. Notes on during operation of PLL clock mode
On this microcontroller, if in case the crystal oscillator breaks off or an external reference clock input stops while
the PLL clock mode is selected, a self-oscillator circuit contained in the PLL may continue its operation at its
self-running frequency. However, Fujitsu will not guarantee results of operation if such failure occurs.
13. When the MB90480/485 series microcontroller is used as a single system
When the MB90480/485 series microcontroller is used as a single system, use connections so the X0A
=
V
SS
,
and X1A
=
Open.
14. Writing to Flash memory
For writing to Flash memory, always ensure that the operating voltage V
CC
is between 3.0 V and 3.6 V.
X0
X1
OPEN
相關PDF資料 |
PDF描述 |
|---|---|
| MB90485 | 16-bit Proprietary Microcontroller |
| MB90487B | 16-bit Proprietary Microcontroller |
| MB90487BPF | 16-bit Proprietary Microcontroller |
| MB90487BPFV | 16-bit Proprietary Microcontroller |
| MB90488B | 16-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90483CPMC | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Microcontroller |
| MB90485 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90485B | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Microcontroller |
| MB90487B | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90487BPF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。