參數資料
型號： MB89F202RAPFV-GE1
廠商： FUJITSU LTD
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 12.5 MHz, MICROCONTROLLER, PDSO34
封裝： 11 X 6.1 MM, 1.45 MM HEIGHT, 0.65 MM PITCH, PLASTIC, SSOP-34
文件頁數： 3/48頁
文件大?。?/td> 608K
代理商： MB89F202RAPFV-GE1
MB89202RA Series
11
■ HANDLING DEVICES
Preventing Latchup
Latchup may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- and high-voltage pins or if higher than the voltage which shows on “1. Absolute Maximum
Ratings” in section “
■ ELECTRICAL CHARACTERISTICS” is applied between VCC and VSS.
When latchup occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Treatment of Unused Input Pins
Leaving unused input terminals open may lead to permanent damage due to malfunction and latchup; pull up
or pull down the terminals through the resistors of 2 k
or more.
Make the unused I/O terminal in a state of output and leave it open or if it is in an input state, handle it with the
same procedure as the input terminals.
Treatment of NC Pins
Be sure to leave (internally connected) NC pins open.
Power Supply Voltage Fluctuations
Although VCC power supply voltage is assured to operate within the rated range, a rapid fluctuation of the voltage
could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC is therefore
important. As stabilization guidelines, it is recommended to control power so that VCC ripple fluctuations (P-P
value) will be less than 10
% of the standard VCC value at the commercial frequency (50 Hz/60 Hz) and the
transient fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power
is switched.
Precautions when Using an External Clock
When an external clock is used, oscillation stabilization time is required even for power-on reset (optional) and
wake-up from stop mode.
About the Wild Register Function
No wild register can be debugged on the MB89V201. For the operation check, test the MB89F202RA installed
on a target system.
Program Execution in RAM
When the MB89V201 is used, no program can be executed in RAM.
Note to Noise in the External Reset Pin (RST)
If the reset pulse applied to the external reset pin (RST) does not meet the specifications, it may cause malfunc-
tions. Use caution so that the reset pulse less than the specifications will not be fed to the external reset pin (RST).
External pullup for the External Reset Pin (RST)
Internal pullup control for RST pin is not available for MB89F202RA. To ensure proper external reset control in
MB89F202RA, an external pullup (recommend 100 k
) for RST pin must be required. Please also check section
“
■ PROGRAMMING AND ERASE FLASH MEMORY”.
(Continued)
相關PDF資料
PDF描述
MB89F202YPFV 8-BIT, FLASH, 12.5 MHz, MICROCONTROLLER, PDSO34
MB89N202-PSH 8-BIT, FLASH, 12.5 MHz, MICROCONTROLLER, PDIP32
MB89F202-PSH 8-BIT, FLASH, 12.5 MHz, MICROCONTROLLER, PDIP32
MB89202-PSH 8-BIT, MROM, 12.5 MHz, MICROCONTROLLER, PDIP32
MB89F201-PSH 8-BIT, FLASH, 12.5 MHz, MICROCONTROLLER, PDIP32
相關代理商/技術參數
參數描述
MB89F202YPFV-ES 制造商:FUJITSU 功能描述:
MB89F499 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller CMOS
MB89F499PF 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller CMOS
MB89F499PFV 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller CMOS
MB89F538 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Original Microcontroller CMOS, F-2MC-8L MB89530A Series
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*