- 您現在的位置：買賣IC網 > PDF目錄377915 > MB89673R (Fujitsu Limited) Hex Schmitt-trigger Inverters 20-LCCC -55 to 125 PDF資料下載
參數資料
| 型號： | MB89673R |
| 廠商： | Fujitsu Limited |
| 英文描述： | Hex Schmitt-trigger Inverters 20-LCCC -55 to 125 |
| 中文描述： | 8位微控制器專有 |
| 文件頁數： | 44/59頁 |
| 文件大?。?/td> | 795K |
| 代理商： | MB89673R |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
44
MB89670/A Series
5. A/D Converter Electrical Characteristics
(AV
CC
= V
CC
= +3.5 V to +6.0 V, F
C
= 10 MHz, AV
SS
= V
SS
= 0.0 V, T
A
= –40
°
C to +85
°
C)
Value
Precautions: The smaller | AVR – AV
SS
|, the greater the error would become relatively.
The output impedance of the external circuit for the analog input must satisfy the following conditions:
Output impedance of the external circuit < Approx. 10 k
If the output impedance of the external circuit is too high, an analog voltage sampling time might be
insufficient (sampling time = 6
μ
s at 10 MHz oscillation).
An analog input equivalent circuit is shown below.
Since the A/D converter contains sample hold circuit, the level of the analog input pin might not stabilize within the
sampling period after A/D activation, resulting in inaccurate A/D conversion values, if the input impedance to the
analog pin is too high. Be sure to maintain an appropriate input impedance to the analog pin.
It is recommended to keep the input impedance to the analog pin not exceed 10 k
. If it exceeds 10 k
, it is
recommended to connect a capacitor of approx. 0.1
μ
F for the analog input pin.
Except for the sampling period after A/D activation, the input leakage current of the analog input pin is less than 10
μ
A.
Parameter
Symbol
Pin
Unit
Remarks
Min.
Typ.
Max.
Resolution
—
—
—
—
10
±
2.0
±
1.5
±
3.0
bit
Linearity error
—
—
LSB
AV
CC
=
AVR = V
CC
Differential linearity error
—
—
LSB
Total error
—
—
LSB
Zero transition voltage
V
OT
AN0 to AN7
AV
SS
– 1.5 LSB
AV
SS
+ 0.5 LSB
AV
SS
+ 2.5 LSB
mV
Full-scale transition
voltage
V
FST
AN0 to AN7
AVR – 3.5 LSB
AVR – 1.5 LSB
AVR + 0.5 LSB
mV
Interchannel disparity
—
—
—
—
4
LSB
A/D mode conversion
time
—
—
13.2
μ
s
At 10-MHz
oscillation
Analog port input current
I
AIN
AN0 to AN7
—
—
10
μ
A
V
Analog input voltage
—
AN0 to AN7
0
—
AVR
Reference voltage
AVR
0
—
AV
CC
V
Reference voltage
supply current
I
R
AVR
—
200
μ
A
AVR = 5.0 V
Comparator
C ..
R ..
(
Sample hold circuit
Close for approx. 15 instruction cycles
after activating A/D conversion.
Analog channel selector
R
≤
10 k
is
recommended.
AN
If R > 10 k
, it is recommended
to connect an external capacitor
of approx. 0.1
μ
F.
Microcontroller’s internal circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MB89P677A | 0.66A, 2.7-5.5V Single Power Distribution Switch IC Hi-Side MOSFET, Fault Report, Act-Low Enable 8-SOIC |
| MB89673RPFM | Hex Schmitt-trigger Inverters 14-CDIP -55 to 125 |
| MB89677APF | Octal Buffers/Drivers With 3-State Outputs 20-LCCC -55 to 125 |
| MB89677APFM | Octal Buffers/Drivers With 3-State Outputs 20-CDIP -55 to 125 |
| MB89P677APF | 8-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB89673RPF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89673RPFM | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89675AR | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89675ARPF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89675ARPFM | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。