- 您現(xiàn)在的位置：買賣IC網 > PDF目錄377914 > MB89647PFM (FUJITSU LTD) Quadruple 2-Input Positive-AND Gates 14-CFP -55 to 125 PDF資料下載
參數資料
| 型號： | MB89647PFM |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Quadruple 2-Input Positive-AND Gates 14-CFP -55 to 125 |
| 中文描述： | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | PLASTIC, QFP-80 |
| 文件頁數： | 15/59頁 |
| 文件大?。?/td> | 774K |
| 代理商： | MB89647PFM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
15
MB89640 Series
I
HANDLING DEVICES
1. Preventing Latchup
Latchup may occur on CMOS ICs if voltage higher than V
CC
or lower than V
SS
is applied to input and output pins
other than medium- to high-voltage pins or if higher than the voltage which shows on “1. Absolute Maximum
Ratings” in section “
I
Electrical Characteristics” is applied between V
CC
and V
SS
.
When latchup occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Also, take care to prevent the analog power supply (AV
CC
and AVRH) and analog input from exceeding the digital
power supply (V
CC
) when the analog system power supply is turned on and off.
2. Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down
resistor.
3. Treatment of Power Supply Pins on Microcontrollers with A/D and D/A Converters
Connect to be AV
CC
= DAVC = V
CC
and AV
SS
= AVRH = V
SS
even if the A/D and D/A converters are not in use.
4. Treatment of N.C. Pins
Be sure to leave (internally connected) N.C. pins open.
5. Power Supply Voltage Fluctuations
Although V
CC
power supply voltage is assured to operate within the rated range, a rapid fluctuation of the voltage
could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC is therefore
important. As stabilization guidelines, it is recommended to control power so that V
CC
ripple fluctuations (P-P
value) will be less than 10% of the standard V
CC
value at the commercial frequency (50 to 60 Hz) and the transient
fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power is switched.
6. Precautions when Using an External Clock
Even when an external clock is used, oscillation stabilization time is required for power-on reset (optional) and
wake-up from stop mode.
相關PDF資料 |
PDF描述 |
|---|---|
| MB89PV650A | Automotive Catalog Power-Distribution Switch 8-SOIC -40 to 85 |
| MB89656APF | 8-bit Proprietary Microcontroller |
| MB89656APFV | 8-bit Proprietary Microcontroller |
| MB89656AR | 8-bit Proprietary Microcontroller |
| MB89653APF | DUAL RETRIGGERABLE MONOSTABLE MULTIVIBRATORS 20-LCCC -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB89650AR | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89653APF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89653APFV | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89653AR | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89655APF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
發(fā)布緊急采購，3分鐘左右您將得到回復。