- 您現在的位置：買賣IC網 > PDF目錄377905 > MB89480 (Fujitsu Limited) 8-bit Proprietary Microcontroller PDF資料下載
參數資料
| 型號： | MB89480 |
| 廠商： | Fujitsu Limited |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-bit Proprietary Microcontroller |
| 中文描述： | 8位微控制器專有 |
| 文件頁數： | 15/55頁 |
| 文件大?。?/td> | 477K |
| 代理商： | MB89480 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
MB89480/480L Series
15
I
HANDLING DEVICES
1.
Preventing Latch-up
Latch-up may occur on CMOS IC if voltage higher than V
CC
or lower than V
SS
is applied to input and output pins
other than medium- to high-voltage pins or if higher than the voltage which shows on “1. Absolute Maximum
Ratings” in
I
ELECTRICAL CHARACTERISTICS is applied between V
CC
and V
SS
.
When latch-up occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Also, take care to prevent the analog power supply (AV
CC
) and analog input from exceeding the digital power
supply (V
CC
) when the analog system power supply is turned on and off.
Treatment of Unused Input Pins
2.
Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down
resistor.
Treatment of Power Supply Pins on Microcontrollers with A/DConverter
3.
Connect to be AV
CC
= V
CC
and AV
SS
= V
SS
even if the A/D converter is not in use.
Treatment of N.C. Pins
4.
Be sure to leave (internally connected) N.C. pins open.
Power Supply Voltage Fluctuations
5.
Although V
CC
power supply voltage is assured to operate within the rated range, a rapid fluctuation of the voltage
could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC is therefore
important. As stabilization guidelines, it is recommended to control power so that V
CC
ripple fluctuations (P-P
value) will be less than 10% of the standard V
CC
value at the commercial frequency (50 to 60 Hz) and the transient
fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power is switched.
Precautions when Using an External Clock
6.
Even when an external clock is used, oscillation stabilization time is required for power-on reset and wake-up
from stop mode.
Notes on noise in the External Reset Pin (RST)
7.
If the reset pulse applied to the external reset pin (RST) does not meet the specifications, it may cause malfunc-
tions. Use caution so that the reset pulse less than the specifications will not be fed to the external reset pin (RST).
相關PDF資料 |
PDF描述 |
|---|---|
| MB89480L | 8-bit Proprietary Microcontroller |
| MB89485LPFM | 8-bit Proprietary Microcontroller |
| MB89485LP-SH | 8-bit Proprietary Microcontroller |
| MB89485PFM | 8-bit Proprietary Microcontroller |
| MB89485P-SH | 8-bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB89480L | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89485 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89485L | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89485LPFM | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89485LP-SH | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。