- 您現在的位置：買賣IC網 > PDF目錄377905 > MB89194 (Fujitsu Limited) 8-Bit Proprietary Microcontroller(8位專用微控制器) PDF資料下載
參數資料
| 型號： | MB89194 |
| 廠商： | Fujitsu Limited |
| 英文描述： | 8-Bit Proprietary Microcontroller(8位專用微控制器) |
| 中文描述： | 8位微控制器專利（8位專用微控制器） |
| 文件頁數： | 12/48頁 |
| 文件大?。?/td> | 680K |
| 代理商： | MB89194 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
12
MB89190/190A Series
I
HANDLING DEVICES
1. Preventing Latch
-
up
Latchup may occur on CMOS ICs if voltage higher than V
CC
or lower than V
SS
is applied to input or output pins
other than medium- and high-voltage pins or if higher than the voltage which shows on “ 1. Absolute Maximum
Ratings” in “
I
Electrical Characteristics” is applied between V
CC
to V
SS
.
When latchup occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Also, take care to prevent the analog power supply (AV
CC
and AVR) and analog input from exceeding the digital
power supply (V
CC
) when the analog system power supply is turned on and off.
2. Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions. They should be connected to pull-up or pull-down
resistor.
3. Treatment of Power Supply Pins on Microcontrollers with A/D and D/A Converters
Connect to be AV
CC
=DAVC=V
CC
and AV
SS
=AVR=V
SS
even if the A/D and D/A converters are not in use.
4. Treatment of N.C. Pin
Be sure to leave (internally connected) N.C. pins open.
5. Power Supply Voltage Fluctuations
Although operation is assured within the rated range of V
CC
power supply voltage, a rapid fluctuation of the
voltage could cause malfunctions within the rated range. Stabilizing voltage supplied to the IC is therefore
important. As stabilization guidelines, it is recommended to control power so that V
CC
ripple fluctuations (P-P
value) will be less than 10% of the standard V
CC
value at the commercial frequency (50 to 60 Hz) and the transient
fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power is switched.
6. Precautions when Using an External Clock
Even when an external clock is used, oscillation stabilization time is required for power-on reset (optional) and
release from stop mode.
相關PDF資料 |
PDF描述 |
|---|---|
| MB89P195 | 8-Bit Proprietary Microcontroller(8位專用微控制器) |
| MB89P195A | 8-Bit Proprietary Microcontroller(8位專用微控制器) |
| MB89251A | SERIAL DATA TRANSMITTER / RECEIVER |
| MB89254 | PROGRAMMABLE TIMER |
| MB89255A | PARALLEL DATA I/O INTERFACE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB89195 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89195A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89195AP | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89195APF | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89195AP-SH | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。