參數資料
型號： MB89191P-SH
廠商： FUJITSU LTD
元件分類： 微控制器/微處理器
英文描述： 8-bit Proprietary Microcontroller
中文描述： 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PDIP28
封裝： 1.778 MM PITCH, PLASTIC, SHDIP-28
文件頁數： 12/47頁
文件大小： 634K
代理商： MB89191P-SH
12
MB89190/190A Series
I
HANDLING DEVICES
1. Preventing Latch
-
up
Latchup may occur on CMOS ICs if voltage higher than V
CC
or lower than V
SS
is applied to input or output pins
other than medium- and high-voltage pins or if higher than the voltage which shows on “ 1. Absolute Maximum
Ratings” in “
I
Electrical Characteristics” is applied between V
CC
to V
SS
.
When latchup occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Also, take care to prevent the analog power supply (AV
CC
and AVR) and analog input from exceeding the digital
power supply (V
CC
) when the analog system power supply is turned on and off.
2. Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions. They should be connected to pull-up or pull-down
resistor.
3. Treatment of Power Supply Pins on Microcontrollers with A/D and D/A Converters
Connect to be AV
CC
=DAVC=V
CC
and AV
SS
=AVR=V
SS
even if the A/D and D/A converters are not in use.
4. Treatment of N.C. Pin
Be sure to leave (internally connected) N.C. pins open.
5. Power Supply Voltage Fluctuations
Although operation is assured within the rated range of V
CC
power supply voltage, a rapid fluctuation of the
voltage could cause malfunctions within the rated range. Stabilizing voltage supplied to the IC is therefore
important. As stabilization guidelines, it is recommended to control power so that V
CC
ripple fluctuations (P-P
value) will be less than 10% of the standard V
CC
value at the commercial frequency (50 to 60 Hz) and the transient
fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power is switched.
6. Precautions when Using an External Clock
Even when an external clock is used, oscillation stabilization time is required for power-on reset (optional) and
release from stop mode.
相關PDF資料
PDF描述
MB89193P-SH 8-bit Proprietary Microcontroller
MB89193PF 8-bit Proprietary Microcontroller
MB89191 8-Bit Proprietary Microcontroller(8位專用微控制器)
MB89191A 8-Bit Proprietary Microcontroller(8位專用微控制器)
MB89193 8-Bit Proprietary Microcontroller(8位專用微控制器)
相關代理商/技術參數
參數描述
MB89193 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller CMOS
MB89193A 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller CMOS
MB89193AH 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller
MB89193AHP 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller
MB89193AHPF 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*