參數資料
型號: MB15E03SLPFV1
廠商: FUJITSU LTD
元件分類: XO, clock
英文描述: Single Serial Input PLL Frequency Synthesizer On-Chip 1.2 GHz Prescaler
中文描述: PLL FREQUENCY SYNTHESIZER, 1200 MHz, PDSO16
封裝: PLASTIC, SSOP-16
文件頁數: 10/22頁
文件大?。?/td> 174K
代理商: MB15E03SLPFV1
10
MB15E03
When designing a synthesizer, the FC pin setting depends on the VCO and LPF characteristics.
Power Saving Mode (Intermittent Mode Control Circuit)
Setting a PS pin to Low, the IC enters into power saving mode resultatly current sonsumption can be limited to
10
μ
A (max.). Setting PS pin to High, power saving mode is released so that the IC works normally.
In addition, the intermittent operation control circuit is included which helps smooth start up from the power saving
mode. In general, the power consumption can be saved by the intermittent operation that powering down or waking
up the synthesizer. Such case, if the PLL is powered up uncontrolled, the resulting phase comparator output signal
is unpredictable due to an undefined phase relation between reference frequency (f
r
) and comparison frequency
(f
p
) and may in the worst case take longer time for lock up of the loop.
To prevent this, the intermittent operation control circuit enforces a limited error signal output of the phase detector
during power up, thus keeping the loop locked.
During the power saving mode, the corresponding section except for indispensable circuit for the power saving
function stops working, then current consumption is reduced to 10
μ
A (max.).
At that time, the Do and LD become the same state as when a loop is locking. That is, the Do becomes high
impedance.
A VCO control voltage is naturally kept at the locking voltage which defined by a LPF”s time constant. As a result
of this, VCO’s frequency is kept at the locking frequency.
Note:
While the power saving mode is executed, ZC pin should be set at ”H” or open. If ZC is set at ”L”
during power saving mode, approximately 10
μ
A current flows.
PS pin must be set ”L” at Power-ON.
The power saving mode can be released (PS : L
H) 1
μ
s later after power supply remains stable.
During the power saving mode, it is possible to input the serial data.
Table.8 PS Pin Setting
PS pin
Status
H
Normal mode
L
Power saving mode
LPF Input Voltage
VCO
Output
Frequency
(1)
(2)
:
When the LPF and VCO characteristics are
similar to (1), set FC bit high.
: When the VCO characteristics are similar to
(2), set FC bit low.
PLL
LPF
VC
相關PDF資料
PDF描述
MB15E03SLPV1 Single Serial Input PLL Frequency Synthesizer On-Chip 1.2 GHz Prescaler
MB15E05L Single Serial Input PLL Frequency Synthesizer On-Chip 1.2 GHz Prescaler
MB15F02L Dual Serial Input PLL Frequency Synthesizer
MB15F02LPFV1 Dual Serial Input PLL Frequency Synthesizer
MB15F02LPV Dual Serial Input PLL Frequency Synthesizer
相關代理商/技術參數
參數描述
MB15E03SLPFV1-G-BND-6 制造商:FUJITSU 功能描述:
MB15E03SLPFV1-G-BND-6E1 功能描述:IC SYNTHESIZER PLL 1.2GHZ 16SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器,PLL,頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 頻率合成器 PLL:是 輸入:晶體 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:1 差分 - 輸入:輸出:無/無 頻率 - 最大:1GHz 除法器/乘法器:是/無 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-LSSOP(0.175",4.40mm 寬) 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:NJW1504V-TE1-NDNJW1504V-TE1TR
MB15E03SLPFV1-G-BND-ER-6E1 制造商:FUJITSU 功能描述:
MB15E03SLPFV1-G-ER-6E1 功能描述:IC SYNTHESIZER PLL 1.2GHZ 16SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器,PLL,頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 頻率合成器 PLL:是 輸入:晶體 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:1 差分 - 輸入:輸出:無/無 頻率 - 最大:1GHz 除法器/乘法器:是/無 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-LSSOP(0.175",4.40mm 寬) 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:NJW1504V-TE1-NDNJW1504V-TE1TR
MB15E03SLPV1 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Single Serial Input PLL Frequency Synthesizer On-Chip 1.2 GHz Prescaler