參數資料
型號： MAXQ622-KIT#
廠商： Maxim Integrated Products
文件頁數： 22/35頁
文件大小： 0K
描述： EVALUATION KIT FOR MAXQ622
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
系列： MAXQ®
類型： MCU
適用于相關產品： MAXQ622
所含物品： 2 個板，線纜，CD
相關產品： MAXQ622X-0000+-ND - IC MCU 16BIT IR MOD BARE DIE
MAXQ622G-0000+-ND - IC MCU 16BIT 128KB IR MOD 64LQFP
其它名稱： 90-M6900#KIT
29
Maxim Integrated
16-Bit Microcontrollers with
Infrared Module and Optional USB
MAXQ612/MAXQ622
mode to minimize power consumption. This feature is
enabled using the power-fail monitor disable (PFD) bit
in the PWCN register. The reset default state for the PFD
bit is 1, which disables the power-fail monitor function
during stop mode. If power-fail monitoring is disabled
(PFD = 1) during stop mode, the circuitry responsible
for generating a power-fail warning or reset is shut down
and neither condition is detected. Thus, the VDD < VRST
condition does not invoke a reset state. However, in the
event that VDD falls below the POR level, a POR is gen-
erated. The power-fail monitor is enabled prior to stop
mode exit and before code execution begins. If a power-
fail warning condition (VDD < VPFW) is then detected,
the power-fail interrupt flag is set on stop mode exit. If a
power-fail reset condition is detected (VDD < VRST), the
CPU goes into reset.
Power-Fail Warning
The power-fail monitor can assert an interrupt if the volt-
age falls below a configurable threshold between the
operating voltage and the reset voltage. This, if enabled,
can allow the firmware to perform housekeeping tasks if
the voltage level decays below the warning threshold.
The power-fail threshold value should only be changed
when the power-fail warning interrupt is disabled (CKCN.
PFIE = 0) to prevent unintended triggering of the power-
fail warning condition.
The power-fail warning threshold is reset to 1.8V by a
POR and is not affected by other resets. See Table 4.
Power-Fail Detection
Figures 5, 6, and 7 show the power-fail detection and
response during normal and stop-mode operation.
If a reset is caused by a power-fail, the power-fail monitor
can be set to one of the following intervals:
Always on—continuous monitoring
211 nanopower ring oscillator clocks (~256ms)
212 nanopower ring oscillator clocks (~512ms)
213 nanopower ring oscillator clocks (~1.024s)
In the case where the power-fail circuitry is periodically
turned on, the power-fail detection is turned on for two
Table 4. Power-Fail Warning Level Selection
Figure 5. Power-Fail Detection During Normal Operation
A
B
C
D
F
G
H
I
E
VDD
VPFW
VRST
VPOR
INTERNAL RESET
(ACTIVE HIGH)
t
< tPFW
t
≥ tPFW
t
≥ tPFW
t
≥ tPFW
PWCN.PFWARNCN[1:0]
PFW THRESHOLD
(V)
00
1.8
01
1.9
10
2.55
11
2.75
相關PDF資料
PDF描述
GBM31DCCH CONN EDGECARD 62POS R/A .156 SLD
ADR4530BRZ-R7 IC VREF SERIES PREC 3V 8SOIC
GBM31DCCD CONN EDGECARD 62POS R/A .156 SLD
GCM24DCBS CONN EDGECARD 48POS R/A .156 SLD
ADR4550BRZ-R7 IC VREF SERIES PREC 5V 8-SOIC
相關代理商/技術參數
參數描述
MAXQ622-KIT# 功能描述:開發板和工具包 - 其他處理器 MAXQ622 Eval Kit RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
MAXQ622X-0000+ 功能描述:16位微控制器 - MCU 16-Bit MCU w/Infrared Module RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MAXQ622X-UEI+ 制造商:Maxim Integrated Products 功能描述:MAXQ622 BLANK WLF FW SCRT UEI - Gel-pak, waffle pack, wafer, diced wafer on film
MAXQ7665A 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit RISC Microcontroller-Based Smart Data-Acquisition Systems
MAXQ7665AATM+ 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit RISC Microcontroller-Based Smart Data-Acquisition Systems
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*