參數資料
型號： MAXQ613E-0000+
廠商： Maxim Integrated Products
文件頁數： 4/28頁
文件大小： 0K
描述： IC MCU 16BIT IR MOD 32LQPF
標準包裝： 250
系列： MAXQ®
核心處理器： RISC
芯體尺寸： 16-位
速度： 12MHz
連通性： SPI，UART/USART
外圍設備： 欠壓檢測/復位，紅外線，電源故障，POR，WDT
輸入/輸出數： 20
程序存儲器容量： 48KB（48K x 8）
程序存儲器類型： 閃存
RAM 容量： 1.5K x 8
電壓 - 電源 (Vcc/Vdd)： 1.7 V ~ 3.6 V
振蕩器型： 內部
工作溫度： 0°C ~ 70°C
封裝/外殼： 32-LQFP
包裝： 管件
其它名稱： 90-M3600+E00
12
Maxim Integrated
16-Bit Microcontroller with Infrared Module
MAXQ613
Memory
The microcontroller incorporates several memory types:
48KB program flash memory
1.5KB SRAM data memory
5.5KB utility ROM
Soft stack
Memory Protection
The optional memory-protection feature separates code
memory into three areas: system, user loader, and user
application. Code in the system area can be kept con-
fidential. Code in the user areas can be prevented from
reading and writing system code. The user loader can
also be protected from user application code.
Memory protection is implemented using privilege levels
for code. Each area has an associated privilege level.
RAM/ROM are assigned privilege levels as well. Refer to
the MAXQ610 User’s Guide for a more thorough expla-
nation of the topic. See Table 1.
Stack Memory
The device provides a soft stack that can be used to
store program return addresses (for subroutine calls
and interrupt handling) and other general-purpose data.
This soft stack is located in the 1.5KB SRAM data
memory, which means that the SRAM data memory must
be shared between the soft stack and general-purpose
application data storage. However, the location and
size of the soft stack is determined by the user, provid-
ing maximum flexibility when allocating resources for a
particular application. The stack is used automatically
by the processor when the CALL, RET, and RETI instruc-
tions are executed and when an interrupt is serviced. An
application can also store and retrieve values explicitly
using the stack by means of the PUSH, POP, and POPI
instructions.
The SP pointer indicates the current top of the stack,
which initializes by default to the top of the SRAM data
memory. As values are pushed onto the stack, the SP
pointer decrements, which means that the stack grows
downward towards the bottom (lowest address) of the
data memory. Popping values off the stack causes the
SP pointer value to increase. Refer to the MAXQ610
User’s Guide for more details.
Utility ROM
The utility ROM is a 5.5KB block of internal ROM memory
located in program space beginning at address 8000h.
This ROM includes the following routines:
In-system programming (bootstrap loader) using
JTAG interface
In-circuit debugging routines using JTAG interface
Production test routines (internal memory tests,
memory loader, etc.), which are used for internal
testing only, and are generally of no use to the end-
application developer
User-callable routines for in-application flash program-
ming, buffer copying, and fast table lookup (more
information on these routines can be found in the
MAXQ610 User’s Guide)
Following any reset, execution begins in the utility ROM
at address 8000h. At this point, unless loader mode or
test mode has been invoked (which requires special pro-
gramming through the JTAG interface), the utility ROM in
the device always automatically jumps to location 0000h,
which is the beginning of user application code in pro-
gram flash memory.
Some applications require protection against unauthor-
ized viewing of program code memory. For these appli-
cations, access to in-system programming, in-applica-
tion programming, or in-circuit debugging functions is
prohibited until a password has been supplied. Three
Table 1. Memory Areas and Associated Maximum Privilege Levels
AREA
PAGE ADDRESS
MAXIMUM PRIVILEGE LEVEL
System
0 to ULDR-1
High
User Loader
ULDR to UAPP-1
Medium
User Application
UAPP to top
Low
Utility ROM
N/A
High
Other (RAM)
N/A
Low
相關PDF資料
PDF描述
73S1210F-44IM/F/P IC SMART CARD READER PROG 44-QFN
73S1209F-68IM/F/P IC SMART CARD READER PROG 68-QFN
73S1209F-44IMR/F/P IC SMART CARD READER PROG 44-QFN
73S1209F-44IM/F/P IC SMART CARD READER PROG 44-QFN
AKSPT-G-BLU-R CONN SHUNT 2.54MM GOLD 6.0MM BLU
相關代理商/技術參數
參數描述
MAXQ613E-0000+ 功能描述:16位微控制器 - MCU Integrated Circuits (ICs) Embedded - Microcontrollers - Application Specific - IC MCU 16BIT IR MOD 32LQPF RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MAXQ613J-0000+ 功能描述:16位微控制器 - MCU 16-Bit MCU w/Infrared Module RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MAXQ613K-0000+ 功能描述:16位微控制器 - MCU Integrated Circuits (ICs) Embedded - Microcontrollers - Application Specific - IC MCU 16BIT IR MOD 44TQFP RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MAXQ613X-0000+ 功能描述:16位微控制器 - MCU 16-Bit MCU w/Infrared Module RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MAXQ614 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit Microcontroller with Infrared Module
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*