- 您現在的位置：買賣IC網 > PDF目錄10923 > MAXQ612G-0000+ (Maxim Integrated Products)IC MCU 16BIT 128KB IR MOD 64LQFP PDF資料下載
參數資料
| 型號： | MAXQ612G-0000+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 16/35頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 16BIT 128KB IR MOD 64LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 160 |
| 系列： | MAXQ® |
| 核心處理器： | RISC |
| 芯體尺寸： | 16-位 |
| 速度： | 12MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，紅外線，電源故障，POR，WDT |
| 輸入/輸出數： | 44 |
| 程序存儲器容量： | 128KB（128K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 6K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.7 V ~ 3.6 V |
| 振蕩器型： | 內部 |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 64-LQFP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
23
Maxim Integrated
16-Bit Microcontrollers with
Infrared Module and Optional USB
MAXQ612/MAXQ622
ROM consists of subroutines that can be called from
application software. These include the following:
In-system programming (bootstrap loader) using
JTAG interface
In-circuit debug routines
Test routines (internal memory tests, memory loader,
etc.)
User-callable routines for in-application flash memory
programming and fast table lookup
Following any reset, execution begins in the utility ROM.
The ROM software determines whether the program
execution should immediately jump to location 0000h,
the start of system code, or to one of the special rou-
tines mentioned. Routines within the utility ROM are user
accessible and can be called as subroutines by the
application software. More information on the utility ROM
functions is contained in the MAXQ622 User’s Guide.
Some applications require protection against unau-
thorized viewing of program code memory. For these
applications, access to in-system programming, in-
application programming, or in-circuit debugging func-
tions is prohibited until a password has been supplied.
The password is defined as the 16 words of physical
program memory at addresses 0010h to 001Fh.
Three password locks protect three different program
memory segments. When the PWL is set to one (power-
on reset default) and the contents of the memory at
addresses 0010h to 001Fh are any value other than FFh
or 00h, the password is required to access the utility
ROM, including in-circuit debug and in-system program-
ming routines that allow reading or writing of internal
memory. When PWL is cleared to zero, these utilities are
fully accessible without password. The PWLS bit uses a
password that is at ULDR + 0010 to ULDR + 001F, and
the PWLL uses a password at UAPP + 0010 to UAPP +
001F. The password is automatically set to all ones fol-
lowing a mass erase.
Watchdog Timer
The internal watchdog timer greatly increases system
reliability. The timer resets the device if software execu-
tion is disturbed. The watchdog timer is a free-running
counter designed to be periodically reset by the applica-
tion software. If software is operating correctly, the coun-
ter is periodically reset and never reaches its maximum
count. However, if software operation is interrupted,
the timer does not reset, triggering a system reset and
optionally a watchdog timer interrupt. This protects the
system against electrical noise or electrostatic discharge
(ESD) upsets that could cause uncontrolled processor
operation. The internal watchdog timer is an upgrade to
older designs with external watchdog devices, reducing
system cost and simultaneously increasing reliability.
The watchdog timer functions as the source of both the
watchdog timer timeout and the watchdog timer reset.
The timeout period can be programmed in a range of
215 to 224 system clock cycles. An interrupt is gener-
ated when the timeout period expires if the interrupt
is enabled. All watchdog timer resets follow the pro-
grammed interrupt timeouts by 512 system clock cycles.
If the watchdog timer is not restarted for another full
interval in this time period, a system reset occurs when
the reset timeout expires.
IR Carrier Generation
and Modulation Timer
The dedicated IR timer/counter module simplifies low-
speed infrared (IR) communication. The IR timer imple-
ments two pins (IRTX and IRRX) for supporting IR
transmit and receive, respectively. The IRTX pin has no
corresponding port pin designation, so the standard
PD, PO, and PI port control status bits are not present.
However, the IRTX pin output can be manipulated high
or low using the PWCN.IRTXOUT and PWCN.IRTXOE
bits when the IR timer is not enabled (i.e., IREN = 0).
Table 2. Watchdog Interrupt Timeout (Sysclk = 12MHz, CD[1:0] = 00)
WD[1:0]
WATCHDOG CLOCK
WATCHDOG INTERRUPT TIMEOUT
WATCHDOG RESET AFTER
WATCHDOG INTERRUPT (s)
00
Sysclk/215
2.7ms
42.7
01
Sysclk/218
21.9ms
42.7
10
Sysclk/221
174.7ms
42.7
11
Sysclk/224
1.4s
42.7
相關PDF資料 |
PDF描述 |
|---|---|
| VI-25T-CV-S | CONVERTER MOD DC/DC 6.5V 150W |
| ISD1750EYIR | IC VOICE REC/PLAY 50SEC 28-TSOP |
| ISD1740EYIR | IC VOICE REC/PLAY 40SEC 28-TSOP |
| ISD1750EYR | IC VOICE REC/PLAY 50SEC 28-TSOP |
| ISD1740SYR | IC VOICE REC/PLAY 40SEC 28-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAXQ612G-0000+ | 功能描述:16位微控制器 - MCU 16-Bit MCU w/Infrared Module RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MAXQ612J-0000 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit Microcontrollers with Infrared Module and Optional USB |
| MAXQ612J-0000+ | 功能描述:16位微控制器 - MCU 16-Bit MCU w/Infrared Module RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MAXQ612J-UEI+ | 制造商:Maxim Integrated Products 功能描述:MAXQ612 BLANK 44 TQFN FW SCRT UEI - Rail/Tube |
| MAXQ612X-UEI+ | 制造商:Maxim Integrated Products 功能描述:MAXQ612 BLANK BARE DIE FW SCRT UEI - Gel-pak, waffle pack, wafer, diced wafer on film |
發布緊急采購，3分鐘左右您將得到回復。