參數資料
型號： MAXQ610X-0001+
廠商： Maxim Integrated Products
文件頁數： 4/29頁
文件大小： 0K
描述： MAXQ610X PROG TESTED DIE WAFFLE
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
系列： MAXQ®
核心處理器： RISC
芯體尺寸： 16-位
速度： 12MHz
連通性： SPI，UART/USART
外圍設備： 欠壓檢測/復位，紅外線，電源故障，POR，WDT
輸入/輸出數： 32
程序存儲器容量： 64KB（64K x 8）
程序存儲器類型： 閃存
RAM 容量： 2K x 8
電壓 - 電源 (Vcc/Vdd)： 1.7 V ~ 3.6 V
振蕩器型： 內部
工作溫度： 0°C ~ 70°C
封裝/外殼： 模具
包裝： 托盤
MAXQ610
16-Bit Microcontroller with Infrared Module
12
______________________________________________________________________________________
Memory Protection
The optional memory-protection feature separates code
memory into three areas: system, user loader, and user
application. Code in the system area can be kept confi-
dential. Code in the user areas can be prevented from
reading and writing system code. The user loader can
also be protected from user application code.
Memory protection is implemented using privilege lev-
els for code. Each area has an associated privilege
level. RAM/ROM are assigned privilege levels as well.
Refer to the
MAXQ610 User’s Guide for a more thor-
ough explanation of the topic. See Table 1.
Stack Memory
A 16-bit-wide internal stack provides storage for program
return addresses and can also be used general-purpose
data storage. The stack is used automatically by the
processor when the CALL, RET, and RETI instructions
are executed and when an interrupt is serviced. An
application can also store values in the stack explicitly by
using the PUSH, POP, and POPI instructions.
On reset, the stack pointer, SP, initializes to the top of
the stack (0Fh). The CALL, PUSH, and interrupt-vector-
ing operations increment SP, then store a value at the
location pointed to by SP. The RET, RETI, POP, and
POPI operations retrieve the value at SP and then
decrement SP.
Utility ROM
The utility ROM is a 5.25KB block of internal ROM mem-
ory that defaults to a starting address of 8000h. The util-
ity ROM consists of subroutines that can be called from
application software. These include the following:
In-system programming (bootstrap loader) using
JTAG interface
In-circuit debug routines
Test routines (internal memory tests, memory loader,
etc.)
User-callable routines for in-application flash pro-
gramming and fast table lookup
Following any reset, execution begins in the utility ROM.
The ROM software determines whether the program
execution should immediately jump to location 0000h,
the start of system code, or to one of the special rou-
tines mentioned. Routines within the utility ROM are
user accessible and can be called as subroutines by
the application software. More information on the utility
ROM functions is contained in the
MAXQ610 User’s
Guide.
Some applications require protection against unautho-
rized viewing of program code memory. For these
applications, access to in-system programming, in-
application programming, or in-circuit debugging func-
tions is prohibited until a password has been supplied.
The password is defined as the 16 words of physical
program memory at addresses 0010h to 001Fh.
Three password locks are provided for protection of up
to three different program memory segments. When the
PWL is set to 1 (POR default) and the contents of the
memory at addresses 0010h to 001Fh are any value
other than FFh or 00h, the password is required to
access the utility ROM, including in-circuit debug and
in-system programming routines that allow reading or
writing of internal memory. When PWL is cleared to 0,
these utilities are fully accessible without password.
The password is automatically set to all ones following
a mass erase.
Watchdog Timer
An internal watchdog timer greatly increases system
reliability. The timer resets the device if software execu-
tion is disturbed. The watchdog timer is a free-running
counter designed to be periodically reset by the appli-
cation software. If software is operating correctly, the
counter is periodically reset and never reaches its max-
imum count. However, if software operation is interrupt-
ed, the timer does not reset, triggering a system reset
and optionally a watchdog timer interrupt. This protects
the system against electrical noise or ESD upsets that
could cause uncontrolled processor operation. The
internal watchdog timer is an upgrade to older designs
with external watchdog devices, reducing system cost
and simultaneously increasing reliability.
AREA
PAGE ADDRESS
MAXIMUM PRIVILEGE LEVEL
System
0 to ULDR-1
High
User Loader
ULDR to UAPP-1
Medium
User Application
UAPP to top
Low
Utility ROM
N/A
High
Other (RAM)
N/A
Low
Table 1. Memory Areas and Associated Maximum Privilege Levels
相關PDF資料
PDF描述
XS1-G02B-FB144-C4 IC MCU 32BIT 16KB OTP 144FBGA
531230-3 SHUNT .200 C/P LP 2 POS 30AU
4-530153-1 CONN SHUNT SPRING 2POS .100 TIN
1-382811-6 SHUNT,ECON,PHBR 15AU,BLACK L/P
530153-2 CONN SHUNT SPRING 2POS .100 GOLD
相關代理商/技術參數
參數描述
MAXQ610X-0001+ 功能描述:MAXQ610X PROG TESTED DIE WAFFLE RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MAXQ® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件
MAXQ610X-2001+ 功能描述:16位微控制器 - MCU RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MAXQ610X-2021+ 制造商:Maxim Integrated Products 功能描述:16-BIT MICROCONTROLLER WITH INFRARED MODULE - Gel-pak, waffle pack, wafer, diced wafer on film
MAXQ610X-UEI+ 制造商:Maxim Integrated Products 功能描述:MAXQ610 BLANK WLP UEI - Gel-pak, waffle pack, wafer, diced wafer on film
MAXQ612 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit Microcontrollers with Infrared Module and Optional USB
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*