- 您現在的位置：買賣IC網 > PDF目錄10951 > MAX9867ETJ+ (Maxim Integrated Products)IC STEREO AUD CODEC LP 32TQFN-EP PDF資料下載
參數資料
| 型號： | MAX9867ETJ+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 43/55頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC STEREO AUD CODEC LP 32TQFN-EP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 60 |
| 類型： | 立體聲音頻 |
| 數據接口： | I²C，串行 |
| 分辨率（位）： | 18 b |
| ADC / DAC 數量： | 2 / 2 |
| 三角積分調變： | 是 |
| 動態范圍，標準 ADC / DAC (db)： | 85 / 90 |
| 電壓 - 電源，模擬： | 1.65 V ~ 1.95 V |
| 電壓 - 電源，數字： | 1.65 V ~ 1.95 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-TQFN-EP（5x5） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
MAX9867
Ultra-Low Power Stereo Audio Codec
48
______________________________________________________________________________________
The slave address with the R/W bit set to 0 indicates
that the master intends to write data to the MAX9867.
The MAX9867 acknowledges receipt of the address
byte during the master-generated 9th SCL pulse.
The second byte transmitted from the master config-
ures the MAX9867’s internal register address pointer.
The pointer tells the MAX9867 where to write the next
byte of data. An acknowledge pulse is sent by the
MAX9867 upon receipt of the address pointer data.
The third byte sent to the MAX9867 contains the data
that is written to the chosen register. An acknowledge
pulse from the MAX9867 signals receipt of the data byte.
The address pointer autoincrements to the next register
address after each received data byte. This autoincre-
ment feature allows a master to write to sequential regis-
ters within one continuous frame. Figure 13 illustrates
how to write to multiple registers with one frame. The
master signals the end of transmission by issuing a
STOP condition. Register addresses greater than 0x17
are reserved. Do not write to these addresses.
Read Data Format
Send the slave address with the R/W bit set to 1 to initi-
ate a read operation. The MAX9867 acknowledges
receipt of its slave address by pulling SDA low during
the 9th SCL clock pulse. A START command followed
by a read command resets the address pointer to reg-
ister 0x00.
The first byte transmitted from the MAX9867 is the con-
tent of register 0x00. Transmitted data is valid on the
rising edge of SCL. The address pointer autoincre-
ments after each read data byte. This autoincrement
feature allows all registers to be read sequentially within
one continuous frame. A STOP condition can be issued
after any number of read data bytes. If a STOP condi-
tion is issued followed by another read operation, the
first data byte to be read is from register 0x00.
The address pointer can be preset to a specific register
before a read command is issued. The master presets
the address pointer by first sending the MAX9867’s
slave address with the R/W bit set to 0 followed by the
register address. A REPEATED START condition is then
sent followed by the slave address with the R/W bit set
to 1. The MAX9867 then transmits the contents of the
specified register. The address pointer autoincrements
after transmitting the first byte.
The master acknowledges receipt of each read byte
during the acknowledge clock pulse. The master must
acknowledge all correctly received bytes except the
last byte. The final byte must be followed by a not
acknowledge from the master and then a STOP condi-
tion. Figure 14 illustrates the frame format for reading 1
byte from the MAX9867. Figure 15 illustrates the frame
format for reading multiple bytes from the MAX9867.
1 BYTE
AUTOINCREMENT INTERNAL
REGISTER ADDRESS POINTER
ACKNOWLEDGE FROM MAX9867
B1 B0
B3 B2
B5 B4
B7 B6
A
0
ACKNOWLEDGE FROM MAX9867
R/W
S
A
1 BYTE
ACKNOWLEDGE FROM MAX9867
B1 B0
B3 B2
B5 B4
B7 B6
P
A
SLAVE ADDRESS
REGISTER ADDRESS
DATA BYTE 1
DATA BYTE n
Figure 13. Writing n Bytes of Data to the MAX9867
ACKNOWLEDGE FROM MAX9867
1 BYTE
AUTOINCREMENT INTERNAL
REGISTER ADDRESS POINTER
ACKNOWLEDGE FROM MAX9867
NOT ACKNOWLEDGE FROM MASTER
A
P
A
0
ACKNOWLEDGE FROM MAX9867
R/W
S
R/W
REPEATED START
Sr
1
SLAVE ADDRESS
REGISTER ADDRESS
SLAVE ADDRESS
DATA BYTE
Figure 14. Reading 1 Byte of Data from the MAX9867
相關PDF資料 |
PDF描述 |
|---|---|
| MCIMX357DVM5BR2 | IC MPU I.MX35 400MAPBGA |
| VI-26V-IY-F1 | CONVERTER MOD DC/DC 5.8V 50W |
| TP3054WM/NOPB | IC FILTER ENHANCE INTERFC 16SOIC |
| MK51DN256ZCMD10 | IC ARM CORTEX MCU 256KB 144BGA |
| VI-26T-IY-F4 | CONVERTER MOD DC/DC 6.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9867ETJ+ | 功能描述:接口—CODEC Stereo Audio CODEC for Portable Devices RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| MAX9867ETJ+T | 功能描述:接口—CODEC Stereo Audio CODEC for Portable Devices RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| MAX9867EVKIT+ | 功能描述:音頻 IC 開發工具 MAX9867 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX9867EWV+ | 制造商:Maxim Integrated Products 功能描述:LOW-POWER, STEREO AUDIO CODEC - Rail/Tube |
| MAX9867EWV+T | 功能描述:接口—CODEC Stereo Audio CODEC for Portable Devices RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。