- 您現在的位置：買賣IC網 > PDF目錄10951 > MAX98089ETN+T (Maxim Integrated Products)IC CODEC AUDIO FLEXSOUND 56TQFN PDF資料下載
參數資料
| 型號： | MAX98089ETN+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 25/131頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CODEC AUDIO FLEXSOUND 56TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | FlexSound™ |
| 類型： | 立體聲音頻 |
| 數據接口： | I²C，串行 |
| 分辨率（位）： | 24 b |
| ADC / DAC 數量： | 2 / 2 |
| 三角積分調變： | 無 |
| S/N 比，標準 ADC / DAC (db)： | 93 / 101 |
| 動態范圍，標準 ADC / DAC (db)： | 93 / 101 |
| 電壓 - 電源，模擬： | 1.65 V ~ 2 V |
| 電壓 - 電源，數字： | 1.65 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 56-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 56-TQFN-EP（7x7） |
| 包裝： | 標準包裝 |
| 其它名稱： | MAX98089ETN+TDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
Low-Power, Stereo Audio Codec
with FlexSound Technology
The slave address with the R/W bit set to 0 indicates
that the master intends to write data to the ICs. The ICs
acknowledge receipt of the address byte during the
master-generated 9th SCL pulse.
The second byte transmitted from the master configures
the IC’s internal register address pointer. The pointer tells
the IC where to write the next byte of data. An acknowl-
edge pulse is sent by the ICs upon receipt of the address
pointer data.
The third byte sent to the ICs contains the data that is writ-
ten to the chosen register. An acknowledge pulse from the
ICs signals receipt of the data byte. The address pointer
autoincrements to the next register address after each
received data byte. This autoincrement feature allows a
master to write to sequential registers within one continu-
ous frame. The master signals the end of transmission by
issuing a STOP condition. Register addresses greater
than 0xC7 are reserved. Do not write to these addresses.
Read Data Format
Send the slave address with the R/W bit set to 1 to initi-
ate a read operation. The IC acknowledges receipt of
its slave address by pulling SDA low during the 9th SCL
clock pulse. A START command followed by a read com-
mand resets the address pointer to register 0x00.
The first byte transmitted from the ICs is the content of
register 0x00. Transmitted data is valid on the rising
edge of SCL. The address pointer autoincrements after
each read data byte. This autoincrement feature allows
all registers to be read sequentially within one continuous
frame. A STOP condition can be issued after any number
of read data bytes. If a STOP condition is issued followed
by another read operation, the first data byte to be read
is from register 0x00.
The address pointer can be preset to a specific register
before a read command is issued. The master presets the
address pointer by first sending the IC’s slave address
with the R/W bit set to 0 followed by the register address.
A REPEATED START condition is then sent followed by the
slave address with the R/W bit set to 1. The IC then trans-
mits the contents of the specified register. The address
pointer autoincrements after transmitting the first byte.
The master acknowledges receipt of each read byte
during the acknowledge clock pulse. The master must
acknowledge all correctly received bytes except the last
byte. The final byte must be followed by a not acknowl-
edge from the master and then a STOP condition. Figure
38 illustrates the frame format for reading one byte from
the IC. Figure 39 illustrates the frame format for reading
multiple bytes from the ICs.
Figure 38. Reading One Byte of Data from the ICs
Figure 39. Reading n Bytes of Data from the ICs
ACKNOWLEDGE FROM MAX98089
NOT ACKNOWLEDGE FROM MASTER
AUTOINCREMENT INTERNAL REGISTER ADDRESS POINTER
1 BYTE
P
REPEATED START
S
OA
A Sr
1
A
SLAVE ADDRESS
REGISTER ADDRESS
SLAVE ADDRESS
DATA BYTE
R/W
ACKNOWLEDGE FROM MAX98089
AUTOINCREMENT INTERNAL REGISTER ADDRESS POINTER
1 BYTE
REPEATED START
S
O
A
Sr
1
A
SLAVE ADDRESS
REGISTER ADDRESS
SLAVE ADDRESS
DATA BYTE
R/W
Maxim Integrated
120
MAX98089
相關PDF資料 |
PDF描述 |
|---|---|
| MCIMX353CVM5B | IC MPU I.MX35 400MAPBGA |
| VI-26X-IY-F1 | CONVERTER MOD DC/DC 5.2V 50W |
| SSM2604CPZ-REEL7 | IC AUDIO CODEC LP 20-LFCSP |
| MCIMX357DVM5B | PROCESSOR MULTIMEDIA 400PBGA |
| VI-26W-IY-F3 | CONVERTER MOD DC/DC 5.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX98089EVKIT#TQFN | 功能描述:音頻 IC 開發工具 MAX98089 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX98089EVKIT#WLP | 功能描述:音頻 IC 開發工具 MAX98089 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX98089EVKIT+TQFN | 功能描述:音頻 IC 開發工具 RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX98089EVKIT+WLP | 功能描述:音頻 IC 開發工具 RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX98089EWY+ | 制造商:Maxim Integrated Products 功能描述:STEREO AUDIO CODEC WITH FLEXSOUND TUNING TECHNOLOGY AND BASI - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。