- 您現在的位置：買賣IC網 > PDF目錄10268 > MAX9778ETI+T (Maxim Integrated Products)IC AMP AUDIO PWR 2.6W AB 28TQFN PDF資料下載
參數資料
| 型號： | MAX9778ETI+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 13/27頁 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| 標準包裝： | 2,500 |
| 類型： | AB 類 |
| 輸出類型： | 2-通道（立體聲）帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 2.6W x 2 @ 4 歐姆; 200mW x 2 @ 16 歐姆 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 特點： | 消除爆音，輸入多路復用器，靜音，關機，熱保護， |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
MAX9777/MAX9778
Stereo 3W Audio Power Amplifiers with
Headphone Drive and Input Mux
20
_
__
_
BIAS Capacitor
BIAS is the output of the internally generated 2.5VDC
bias voltage. The BIAS bypass capacitor, CBIAS,
improves PSRR and THD+N by reducing power supply
and other noise sources at the common-mode bias
node, and also generates the clickless/popless, start-
up/shutdown DC bias waveforms for the speaker ampli-
fiers. Bypass BIAS with a 1F capacitor to GND.
Supply Bypassing
Proper power-supply bypassing ensures low-noise, low-
distortion performance. Place a 0.1F ceramic capacitor
from VDD to GND. Add additional bulk capacitance as
required by the application, typically 100F. Bypass
PVDD with a 100F capacitor to GND. Locate bypass
capacitors as close to the device as possible.
Gain Select
The MAX9777/MAX9778 feature multiple gain settings on
each channel, making available different gain and feed-
back configurations. The gain-setting resistor (RF) is con-
nected between the amplifier output (OUT_+) and the
gain set point (GAIN_). An internal multiplexer switches
between the different feedback resistors depending on
the status of the gain control input. The stereo
MAX9777/MAX9778 feature two gain options per chan-
nel. See Tables 1a and 1b for the gain-setting options.
Bass Boost Circuit
Headphones typically have a poor low-frequency
response due to speaker and enclosure size limitations.
A bass boost circuit compensates the poor low-frequen-
cy response (Figure 10). At low frequencies, the capaci-
tor CF is an open circuit, and the effective impedance in
the feedback loop (RF(EFF)) is RF(EFF) = RF1.
At the frequency:
where the impedance, CF, begins to decrease, and at
high frequencies, the CF is a short circuit. Here the
impedance of the feedback loop is:
Assuming RF1 = RF2, then RF(EFF) at low frequencies is
twice that of RF(EFF) at high frequencies (Figure 11).
Thus, the amplifier has more gain at lower frequencies,
boosting the system’s bass response. Set the gain roll-
off frequency based upon the response of the speaker
and enclosure.
To minimize distortion at low frequencies, use capaci-
tors with low-voltage coefficient dielectrics when select-
ing CF. Film or C0G dielectric capacitors are good
choices for CF. Capacitors with high-voltage coeffi-
cients, such as ceramics (non-C0G dielectrics), can
result in increased distortion at low frequencies.
Layout and Grounding
Good PC board layout is essential for optimizing perfor-
mance. Use large traces for the power-supply inputs
and amplifier outputs to minimize losses due to para-
sitic trace resistance, as well as route heat away from
the device. Good grounding improves audio perfor-
mance, minimizes crosstalk between channels, and
prevents any digital switching noise from coupling into
the audio signal. If digital signal lines must cross over
or under audio signal lines, ensure that they cross per-
pendicular to each other.
The MAX9777/MAX9778 TQFN package features an
exposed thermal pad. This pad lowers the package’s
thermal resistance by providing a direct heat conduc-
tion path from the die to the PC board. Connect the pad
to signal ground (0V) by using a large pad or multiple
vias to the ground plane.
R
RR
F EFF
FF
() =
×
+
12
1
2
πRC
FF
VBIAS
RIN
RF2
RF1
CF
Figure 10. Bass Boost Circuit
RF1
RF1 RF2
RIN
2
π RF2 CF
1
FREQUENCY
GAIN
Figure 11. Bass Boost Response
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2414IGN#TRPBF | IC ADC 8CH 24BIT DIFFINPUT28SSOP |
| MAX9777ETI+T | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| D38999/20KE6SNLC | CONN HSG RCPT 6POS WALL MT SCKT |
| MS27473T24B4SCLC | CONN HSG PLUG 56POS STRGHT SCKT |
| LTC2414IGN#TR | IC ADC 8CH 24BIT DIFFINPUT28SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9779ETI+ | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9779ETI+T | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX977EEE | 功能描述:校驗器 IC 3V/5V Dual-Speed Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX977EEE+ | 功能描述:校驗器 IC 3V/5V Dual-Speed Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX977EEE+T | 功能描述:校驗器 IC 3V/5V Dual-Speed Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。