- 您現在的位置：買賣IC網 > PDF目錄10268 > MAX9777ETI+T (Maxim Integrated Products)IC AMP AUDIO PWR 2.6W AB 28TQFN PDF資料下載
參數資料
| 型號： | MAX9777ETI+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/27頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| 標準包裝： | 2,500 |
| 類型： | AB 類 |
| 輸出類型： | 2-通道（立體聲）帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 2.6W x 2 @ 4 歐姆; 200mW x 2 @ 16 歐姆 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 特點： | 消除爆音，I²C，輸入多路復用器，靜音，關機，熱保護 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
MAX9777/MAX9778
Stereo 3W Audio Power Amplifiers with
Headphone Drive and Input Mux
______________________________________________________________________________________
13
Headphone Sense Input (HPS)
With headphone sense enabled, a voltage on HPS less
than 0.7 x VDD sets the device to speaker mode. A volt-
age greater than 0.9 x VDD disables the inverting
bridge amplifier (OUT_-), which mutes the speaker
amplifier and sets the device into headphone mode.
For automatic headphone detection, enable headphone
sense and connect HPS to the control pin of a 3-wire
headphone jack as shown in Figure 2. With no head-
phone present, the resistive voltage-divider created by
R1 and R2 sets the voltage on HPS to be less than 0.7 x
VDD, setting the device to speaker mode and the gain
setting defaults to GAINA (MAX9777). When a head-
phone plug is inserted into the jack, the control pin is dis-
connected from the tip contact, and HPS is pulled to VDD
through R1, setting the device into headphone mode and
the gain-setting defaults to GAINB (MAX9777) (see the
Gain Select section). Place a resistor in series with the
control pin and HPS (R3) to prevent any audio signal from
coupling into HPS when the device is in speaker mode.
Shutdown
The MAX9777/MAX9778 feature a 10A, low-power
shutdown mode that reduces quiescent current con-
sumption and extends battery life. The drive amplifiers
and bias circuitry are disabled, the amplifier outputs
(OUT_) go high impedance, and BIAS is driven to
GND. Driving
SHDN low places the devices into shut-
down mode, disables the interface, and resets the I2C
registers to a default state. A logic-high on
SHDN
enables the devices.
MAX9777 Software Shutdown
A logic-high on bit 0 of the SHDN register places the
MAX9777 in shutdown mode. A logic-low enables the
device. The digital section of the MAX9777 remains
active when the device is shut down through the inter-
face. All devices feature a logic-low on the
SHDN input.
MUTE
The MAX9777/MAX9778 feature a mute mode. When
the device is muted, the input is disconnected from the
amplifiers. MUTE does not shut down the device.
MAX9777 MUTE
The MAX9777 MUTE mode is selected by writing to the
MUTE register (see the
Mute Register section). The left
and right channels can be independently muted.
MAX9778 MUTE
The MAX9778 features an active-high MUTE input that
mutes all channels.
Click-and-Pop Suppression
The MAX9777/MAX9778 feature Maxim’s comprehen-
sive click-and-pop suppression. When entering or exit-
ing shutdown, the common-mode bias voltage of the
amplifiers is slowly ramped to and from the DC bias
point using an S-shaped waveform. In headphone
mode, this waveform shapes the frequency spectrum,
minimizing the amount of audible components present
at the headphone. In speaker mode, the BTL amplifiers
start up in the same fashion as in headphone mode.
When entering shutdown, both amplifier outputs ramp
to GND quickly and simultaneously. To maximize click-
and-pop suppression, drive
SHDN to 0V before power-
up or power-down transitions.
MAX9777
MAX9778
R3
47k
Ω
R1
680k
Ω
R2
10k
Ω
R2
10k
Ω
HPS
VDD
OUTL+
OUTR+
Figure 2. HPS Configuration Circuit
INPUTS
HPS_EN
HPS
MODE
GAIN PATH*
0
X
BTL
A or B
1
0
BTL
A or B
1
SE
A or B
Table 1b. MAX9778 HPS Setting
*Note:
A or B—Gain path selected by external GAINAB
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/20KE6SNLC | CONN HSG RCPT 6POS WALL MT SCKT |
| MS27473T24B4SCLC | CONN HSG PLUG 56POS STRGHT SCKT |
| LTC2414IGN#TR | IC ADC 8CH 24BIT DIFFINPUT28SSOP |
| MS27473T24B4SBLC | CONN HSG PLUG 56POS STRGHT SCKT |
| D38999/26JJ4PALC | CONN HSG PLUG 56POS STRGHT PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9778ETI+ | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9778ETI+T | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9779ETI+ | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9779ETI+T | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX977EEE | 功能描述:校驗器 IC 3V/5V Dual-Speed Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。