- 您現在的位置：買賣IC網 > PDF目錄10268 > MAX9760EUI+ (Maxim Integrated Products)IC AMP AUDIO PWR 3W STER 28TSSOP PDF資料下載
參數資料
| 型號： | MAX9760EUI+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/31頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO PWR 3W STER 28TSSOP |
| 標準包裝： | 50 |
| 類型： | AB 類 |
| 輸出類型： | 2-通道（立體聲）帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 3W x 2 @ 3 歐姆; 200mW x 2 @ 16 歐姆 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 特點： | 消除爆音，I²C，輸入多路復用器，靜音，關機，熱保護 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 28-TSSOP 裸露焊盤 |
| 封裝/外殼： | 28-SOIC（0.173"，4.40mm 寬）裸露焊盤 |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
MAX9760–MAX9763
Stereo 3W Audio Power Amplifiers with
Headphone Drive and Input Mux
______________________________________________________________________________________
13
When configured as a headphone (single-ended) ampli-
fier, the slave amplifier is disabled, muting the speaker
and the main amplifier drives the headphone. The
MAX9760–MAX9763 can deliver 3W of continuous aver-
age power into a 3
load with less than 1% THD+N in
speaker mode, and 200mW of continuous average
power into a 16
load with less than 1% THD+N in
headphone mode. These devices also feature thermal
overload protection.
Mono Mode
The MAX9762/MAX9763 are 3W mono speaker ampli-
fiers, 200mW stereo headphone amplifiers, and a
mixer/attenuator (see the MAX9762/MAX9763 Functional
Diagram). In speaker (mono) mode, the mixer/attenuator
combines the two stereo inputs (INL_ and INR_) and
attenuates the resultant signal by a factor of 2. This
allows for full reproduction of a stereo signal through a
single speaker, while maintaining optimum headroom.
The resistor connected between GAINM and OUTR+,
sets the gain of the devices in speaker mode (see the
MAX9762 Functional Diagram). This allows the speaker
amplifier to have a different gain and feedback network
from the headphone amplifier.
BIAS
These devices operate from a single 5V supply, and
feature an internally generated, power-supply indepen-
dent, common-mode bias voltage of 2.5V referenced to
GND. BIAS provides both click-and-pop suppression
and sets the DC bias level for the audio outputs. BIAS
is internally connected to the noninverting input of each
speaker amplifier (see Typical Application Circuit/
Functional Diagram). Choose the value of the bypass
capacitor as described in the BIAS Capacitor section.
No external load should be applied to BIAS. Any load
lowers the BIAS voltage, affecting the overall perfor-
mance of the device.
Input Multiplexer
Each amplifier features a 2:1 input multiplexer, allowing
input selection between two stereo sources. Both multi-
plexers are controlled by bit 1 in the control register
(MAX9760/MAX9762) or by the IN1/2 pin (MAX9761/
MAX9763). A logic low selects input IN_1 and a logic
high selects input IN_2.
The input multiplexer can also be used to further
expand the number of gain options available from the
MAX9760–MAX9763 family. Connecting the audio
source to the device through two different input resis-
tors (Figure 1) increases the number of gain options
from two to four (MAX9760/MAX9761) and from three to
six (MAX9762/MAX9763). Additionally, the input multi-
plexer allows a speaker equalization network to be
switched into the speaker signal path. This is typically
useful in optimizing acoustic response from speakers
with small physical dimensions.
Headphone Sense Enable
The HPS pin is enabled by HPS_EN (MAX9762/
MAX9763) or the HPSD bit (MAX9760/MAX9761).
HPSD or HPS_EN determines whether the device is in
automatic detection mode or fixed mode operation (see
Tables 1a and 1b).
Headphone Sense Input (HPS)
A voltage on HPS less than 0.7 VDD sets the device
to speaker mode. A voltage greater than 0.9 VDD dis-
ables the inverting bridge amplifier (OUT_-), which
mutes the speaker amplifier and sets the device into
headphone mode.
For automatic headphone detection, connect HPS to the
control pin of a 3-wire headphone jack as shown in
Figure 2. With no headphone present, the resistive volt-
age-divider created by R1 and R2 sets the voltage on
HPS to be less than 0.7 VDD, setting the device to
speaker mode and the gain setting defaults to GAINA
(MAX9760/MAX9762). When a headphone plug is insert-
ed into the jack, the control pin is disconnected from the
tip contact, and HPS is pulled to VDD through R1, setting
the device into headphone mode and the gain-setting
defaults to GAINB (MAX9760/MAX9762) (see Gain
Select section). Place a resistor in series with the control
pin and HPS (R3) to prevent any audio signal from cou-
pling into HPS when the device is in speaker mode.
Shutdown
The MAX9760–MAX9763 feature a 10A, low-power
shutdown mode that reduces quiescent current con-
sumption and extends battery life. The drive amplifiers
and bias circuitry are disabled, the amplifier outputs
(OUT_) go high impedance, and BIAS is driven to
MAX9760
AUDIO
INPUT
15k
30k
IN_1
IN_2
Figure 1. Using the Input Multiplexer for Gain Setting
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9750AEUI+ | IC AMP AUDIO PWR 2.6W AB 28TSSOP |
| LTC1853CFW | IC A/D CONV 8CH 12BIT 48-TSSOP |
| AD7812WYRUZ | IC ADC 10BIT 8-CHAN SRL 20TSSOP |
| MAX9777ETI+ | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| MAX9778ETI+T | IC AMP AUDIO PWR 2.6W AB 28TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9760EUI+ | 功能描述:IC AMP AUDIO PWR 3W STER 28TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| MAX9760EUI+T | 功能描述:IC AMP AUDIO PWR 3W STER 28TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| MAX9760EVKIT | 功能描述:放大器 IC 開發工具 RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX9760EVSYS | 功能描述:放大器 IC 開發工具 RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX9761ETI | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。