- 您現在的位置：買賣IC網 > PDF目錄384715 > MAX975 (Maxim Integrated Products, Inc.) Single/Dual, +3V/+5V Dual-Speed Comparators with Auto-Standby PDF資料下載
參數資料
| 型號： | MAX975 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Single/Dual, +3V/+5V Dual-Speed Comparators with Auto-Standby |
| 中文描述： | 單/雙路、+3V/+5V雙速度比較器，帶有自動待機功能 |
| 文件頁數： | 11/16頁 |
| 文件大小： | 264K |
| 代理商： | MAX975 |
_______________Detailed Desc ription
The MAX975/MAX977 single/dual comparators have
three operating modes, and use a +2.7V to +5.25V
single supply. The operating modes are as follows:
high speed, high speed with auto-standby, and low
power. Propagation delay is typically 28ns in high-
speed mode, while typical supply current is 250μA. In
low-power mode, propagation delay is typically 480ns
and power consumption is only 3μA. The auto-standby
feature switches into low-power standby for each
comparator with unchanging outputs in high-speed
mode. The timeout period, or the time that OUT_
must be idle (unchanged state) for the MAX975/
MAX977 to enter auto-standby, is adjustable by means
of an external capacitor. All inputs and outputs can tol-
erate a continuous short-circuit fault condition to either
rail. Internal hysteresis in high-speed mode ensures
clean output switching, even with slow-moving input
signals.
The MAX975 functional diagram shows two paralleled
comparators, a timing circuit, a transition detector, and
logic gates. The upper comparator is high speed, while
the lower comparator is a slower low-power compara-
tor. The dual MAX977 features independent timeout
adjustment. The following sections discuss the details
of operation.
Hysteresis (High-S peed Mode Only)
Most high-speed comparators can oscillate in the linear
operating region because of noise or undesired para-
sitic feedback. This tends to occur when the voltage on
one input is equal to or very close to the voltage on the
other input. The MAX975/MAX977 have internal hys-
teresis to counter parasitic effects and noise.
The hysteresis in a comparator creates two trip points:
one for the rising input voltage and one for the falling
input voltage (Figure 1). The difference between the trip
points is the hysteresis. When the comparators’ input
voltages are equal, the hysteresis effectively causes
one comparator input voltage to move quickly past the
other, taking the input out of the region where oscilla-
tion occurs.
Figure 1 illustrates the case where IN- has a fixed volt-
age applied and IN+ is varied. If the inputs were
reversed, the figure would be the same, except with an
inverted output.
Auto-S tandby Mode
The MAX975/MAX977’s auto-standby function operates
only in high-speed mode. The device enters auto-
standby when OUT_ remains unchanged for a prepro-
grammed timeout period. In auto-standby mode, the
low-power comparator is enabled while the high-speed
comparator is disabled and STAT_ goes high. The logic
state and sink/source capabilities of OUT_ remain
unchanged, but propagation delay increases to 480ns.
In this mode, the timing circuitry is powered down, and
the transition detector monitors the low-power com-
parator for a transition. When an output transition
occurs (OUT_ changes state), the timing circuitry is
M
S ingle/Dual, +3V /+5V Dual-S peed
Comparators with Auto-S tandby
______________________________________________________________________________________
11
INPUTS
LP
STO_
IDLE TIME
MODE
STAT
OUTPUT
L
t
ASB
= C
STO
x 10μs/pF
<t
ASB
High speed
(Auto-standby enabled)
L
L
t
ASB
= C
STO
x 10μs/pF
≥
t
ASB
Auto-standby
H
↓
(falling edge)
L
X
High speed
(Auto-standby mode disabled)
L
H
X
X
Low power
H
Table 1. Programming
V
OL
V
OH
V
IN-
= 0
V
OS
=V
TRIP+
+ V
TRIP-
2
COMPARATOR
OUTPUT
V
TRIP+
V
IN+
V
HYST
V
TRIP-
Figure 1. Input and Output Waveforms, Noninverting Input
Varied
相關PDF資料 |
PDF描述 |
|---|---|
| MAX975EUA | Single/Dual, +3V/+5V Dual-Speed Comparators with Auto-Standby |
| MAX976-MAX998 | Single/Dual/Quad, SOT23, Single-Supply, High-Speed, Low-Power Comparators |
| MAX976 | Octal Transparent D-type Latches With 3-State Outputs 20-CDIP -55 to 125 |
| MAX976ESA | Octal Edge-Triggered D-type Flip-Flops With 3-State Outputs 20-CDIP -55 to 125 |
| MAX976EUA | Octal Edge-Triggered D-type Flip-Flops With 3-State Outputs 20-CFP -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9750AETI+ | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9750AETI+T | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9750AEUI+ | 功能描述:IC AMP AUDIO PWR 2.6W AB 28TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:DirectDrive® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| MAX9750AEUI+T | 功能描述:IC AMP AUDIO PWR 2.6W AB 28TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:DirectDrive® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| MAX9750AEVKIT | 功能描述:放大器 IC 開發工具 RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
發布緊急采購，3分鐘左右您將得到回復。