- 您現在的位置：買賣IC網 > PDF目錄10268 > MAX9757ETJ+ (Maxim Integrated Products)IC AMP AUDIO PWR 2.3W AB 32TQFN PDF資料下載
參數資料
| 型號： | MAX9757ETJ+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/31頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO PWR 2.3W AB 32TQFN |
| 標準包裝： | 60 |
| 系列： | DirectDrive® |
| 類型： | AB 類 |
| 輸出類型： | 2-通道（立體聲）帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 2.3W x 2 @ 3 歐姆; 130mW x 2 @ 16 歐姆 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 特點： | 消除爆音，短路保護和熱保護，關機，音量控制 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 32-TQFN-EP（5x5） |
| 封裝/外殼： | 32-WFQFN 裸露焊盤 |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Attack Time
The attack time is the time it takes to reduce the gain
after the input signal has exceeded the threshold level.
Suggested attack time range is from 150s to 50ms.
The gain attenuation in attack is exponential and the
attack time is defined as one time constant. The time
constant of the attack is given by 15,000 x CCT sec-
onds (where CCT is the external timing capacitor).
Use a short attack time for the ALC to react quickly
to transient signals, such as snare drum beats
(music) or gun shots (DVD). Fast attack times can
lead to gain “pumping” where rapid ALC action can
be heard reacting to dynamic material.
Use a longer attack time to allow the ALC to ignore
short-duration peaks and only reduce the gain when
a noticeable increase in loudness occurs. Short-dura-
tion peaks are not reduced, but louder passages are.
This allows the louder passages to be reduced in vol-
ume, thereby maximizing output dynamic range.
Having the attack time too long can possibly result in
some damage to the loudspeaker under harsh condi-
tions.
Hold Time
Hold time is the delay after the signal falls below the
threshold level before the release phase is initiated.
Hold time is internally set to 50ms and nonadjustable.
The hold time is cancelled by any signal exceeding the
set threshold level and attack is reinitiated.
Release Time
The release time is how long it takes for the gain to
return to its normal level after the input signal has fallen
below the threshold level and 50ms hold time has
expired. Release time is defined as release from a 6dB
gain compression to 10% of the nominal gain setting
after the input signal has fallen below PREF threshold
and the 50ms hold time has expired. Release time is
adjustable between 95ms and 10s. The release time is
set by picking an attack time using CCT and setting the
attack to release time ratio by configuring DR as shown
in Table 2. Release time is linear in dB with time and is
inversely proportional to the magnitude of gain com-
pression:
Use a small ratio to maximize the speed of the ALC.
Use a large ratio to maximize the sound quality and
prevent repeated excursions above the threshold
from being independently adjusted by the ALC.
Release and attack times are set by selecting the
capacitance value between CT and GND, and by set-
ting the logic state of DR (Table 1). DR is a tristate logic
input that sets the attack-to-release time ratio. A fixed
hold time of 50ms is internally added to the release time.
MAX9756/MAX9757/MAX9758
2.3W Stereo Speaker Amplifiers and DirectDrive
Headphone Amplifiers with Automatic Level Control
______________________________________________________________________________________
15
OUTPUT
2V/div
CT
1V/div
10ms/div
Figure 4. Attack, Hold, and Release Time
Table 1. Attack and Release Time
ATTACK TIME
RELEASE TIME
TIMING CAPACITOR
(CCT)
DR = ‘X’
DR = VDD
DR = VBIAS
DR = GND
10nF
150s
30ms
95ms
300ms
33nF
495s
99ms
313ms
990ms
100nF
1.5ms
300ms
950ms
3s
330nF
4.95ms
990ms
3.1s
9.9s
1F
15ms
3s
9.5s
—
2.2F
33ms
6.6s
—
3.3F
49.5ms
10s
—
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9750BETI+ | IC AMP AUDIO PWR 2.6W AB 28TQFN |
| MS27656E13F8PC | CONN RCPT 8POS WALL MNT W/PINS |
| AD7683BCPZRL | IC ADC 16BIT 100KSPS 8LFCSP |
| LTC2366HTS8#TRMPBF | IC ADC 12BIT 3MSPS TSOT23-8 |
| D38999/24JH55SALC | CONN HSG RCPT 55POS JAM NUT SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9757ETJ+ | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9757ETJ+T | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9758ETJ+ | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9758ETJ+T | 功能描述:音頻放大器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9759ETE+ | 功能描述:音頻放大器 3.2W Low-EMI Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。